HOOKE ROAD BXG.8280 Discovery Front Bumper Installation Guide
- June 1, 2024
- HOOKE ROAD
Table of Contents
MAKE A DIFFERENCE
Front Bumper
BXG.8280
Contents:
| Qty | Part Name | Size(mm) | Picture |
|---|---|---|---|
| 6 | Hex Bolts | M12*35 | |
| 8 | Hex Bolts | M12*30 | |
| 4 | Hex Bolt | M8*20 | |
| 12 | Button Head Socket Cap Bolts Screws | M6*20 | |
| 14 | Split Lock Washer | D12 | |
| 4 | Split Lock Washer | D8 | |
| 20 | Flat Washer | M12302 | |
| 4 | Flat Washer | M8161 | |
| 4 | Flat Washer | M6121 | |
| 2 | Nylon Round Spacer | M6121.3 | |
| 14 | Hex Nut | M12 | |
| 4 | Flange Hex Lock Nuts | M8 | |
| 4 | Nylon Insert Lock Nut | M6 | |
| 8 | Button Head Socket Cap Bolts Screws | M4*16 | |
| 1 | L-Wrench | M4 | |
| 4 | Sensor Brackets | ||
| --- | --- | --- | --- |
Tools required:
a. Drive Socket Ratchet Wrench;
b. 4mm Hex Bit Socket;
c. 10mm, 13mm, 19mm Wrench;
d. 13mm, 19mm Shallow Socket;
Installation time:
About 2 hours, 2-3 people may be needed. Installation time may differ
according to your mechanical skill level.
(PLEASE VERIFY ALL PARTS ARE PRESENT AND READ INSTRUCTIONS CAREFULLY BEFORE
STARTING INSTALLATION!)
To view the electronic version (BXG.8280), please scan the QR code.
https://drive.google.com/drive/folders/1_sSzO23mBvCEuVcf6s5ILsfg7kmthuGw?usp=sharing
Installation instruction:
Step 1: Remove your factory front bumper. Then check the parts and screws you received and classify them as the contents pictures down.
Step 2: First, in the initial step, connect the wings to the main body using M12*30 hex bolts. Repeat the same procedure on the other side.
Step 3: Install the bull bar to the main body and tighten it with M8*20 hex head screws and nuts.
Step 4: If you need to install the license plate bracket, first you
need to use M620 button head socket cap bolts and nuts to assemble the
license plate bracket. Then, use M620 screws to secure it into the main body,
as shown in the diagram.
Step 5: Lift the bumper, align it with the holes, and secure the bumper
to the vehicle by using M1235 bolts and nuts.
Notes : If you need install the winch power control box bracket, you
should use M&20 hex head screws to install it together with the bumper into
your vehicle. This step isn’t 100% necessary. Depends if you have the winch
power control box.
Step 6: Next, install the provided square lights into the bumper. Use M6*16 black screws for the installation.
(4) Button Head Socket Cap Bolts Screws (M6*16)
Step 7: Finally, adjust the bumper to the appropriate position in the gap with
the car body, then tighten all the screws.
Step 8: The installation is complete. We hope you enjoy a wonderful off- road life with this quality Hooke Road product!
Attontion:
- The product parts in this instruction may differ slightly from the actual product contents but generally docs not affect the installation Of the product.
- Please feel free te contact your distributor if you have any kind of question about your purchase. Go glee Hooke Road to find your parts.
Feel Free To Share Your Vehicle @HookeRaadéx4
With The Hashtag #hookeroad If You’d Like
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>