HOOKE ROAD BXG.3062-S Gladiator JT JL Tubular Stubby Front Bumper Instruction Manual
- June 1, 2024
- HOOKE ROAD
Table of Contents
HOOKE ROAD BXG.3062-S Gladiator JT JL Tubular Stubby Front Bumper
Specifications :
- Model: BXG.3062-S
Parts Included:
- 4 x M10*20 Button Head Socket Cap Bolts Screws
- 7 x M8*20 Button Head Socket Cap Bolts Screws
- 2 x M6*16 Button Head Socket Cap Bolts Screws
- 8 x Split Lock Washer D12
- 7 x Split Lock Washer D10
- 2 x Split Lock Washer D8
- 4 x Flat Washer M12302
- 4 x Flat Washer M10222
- 7 x Flat Washer M8161.5
- 2 x Flat Washer M6121.5
- 8 x Hex Nuts M12
- 4 x Flange Hex Lock Nuts M10
- 7 x Flange Hex Lock Nuts M8
- 2 x Flange Hex Lock Nuts M6
- 2 x D-rings
Tools Required:
- Drive Socket Ratchet Wrench
- 5mm, 6mm Hex Bit Socket
- 9mm Wrench
- 4mm L-Wrench
Installation Time:
About 1 hour, 1-2 people may be needed. Installation time may differ according
to your mechanical skill level.
Installation Instructions:
-
Step 1: Remove the factory front bumper, ready to install ourproduct.
-
Step 2: Connect the wings to the main body using M10*20 button head socket cap bolts screws and nuts on both sides.
-
Step 3: Attach the bull bar to the main body using M8*20 button
head socket cap bolts screw and nuts. -
Step 4: Install the winch bracket on the side of the vehicle’s main beam using factory bolts.
-
Step 5: Lift the bumper, align it with the holes, and tighten the screws on the bar using M12 nuts.
-
Step 6: Secure the license plate frame using M6*16 button head] socket cap bolts screws.
-
Step 7: Optionally, install the decorative plate using M8*20 button head socket cap bolts screws.
-
Step 8: Install the D-ring into the D-ring mount.
-
Step 9: Installation is complete. Enjoy your off-road
adventures with this Hooke Road product!
Attention:
- Product parts may slightly differ from the manual but should not affect installation.
- Contact your distributor for any questions about your purchase.
FAQ:
Q: Can I install this bumper alone?
A: While it’s recommended to have 1-2 people for installation,
experienced individuals can install it alone with proper tools.
Front Bumper
Contents:
Tools required
- Drive Socket Ratchet Wrench;
- 5mm, 6mm Hex Bit Socket;
- 9mm Wrench;
- 4mm L-Wrench
Installation time:
About 1 hour, 1-2 people may be needed. Installation time may differ according
to your mechanical skill level.
(PLEASE VERIFY ALL PARTS ARE PRESENT AND READ INSTRUCTIONS CAREFULLY BEFORE
STARTING INSTALLATION!)
To view the electronic version (BXG.3062-S), please scan the QR code.
Installation instruction:
-
Step 1: Remove the factory front bumper, ready to install our product
-
Step 2: First, in the initial step, connect the wings to the main body using M10*20 button head socket cap bolts screws and nuts. Repeat the same procedure on the other side.
-
Step 3: Connect the bull bar to the main body using M8*20 button head socket cap bolts screw and nuts.
-
Step 4: To install the winch bracket, use the holes on the side of the vehicle’s main beam (as shown in the diagram) with the factory bolts. The winch bracket should be placed behind the vehicle mounting hole.
-
Step 5: Lift the bumper, align it with the holes, and tighten the screws on the bar using M12 nuts.
-
Step 6: If you need to install the license plate frame, you will need to use M6*16 button head socket cap bolts screws to secure it into the bar, as shown in the diagram.
-
Step 7: To install the decorative plate. Use the (M8*20) button head socket cap bolts screws. This step isn’t 100% necessary. Depends if you use the winch.
-
Step 8: Install the D-ring into the D-ring mount. -
Step 9:
The installation is complete. We hope you enjoy a wonderful off-road life with this quality Hooke Road product!
Attention :
- The product parts in this instruction may differ slightly from the actual product contents but generally does not affect the installation of the product.
- Please feel free to contact your distributor if you have any kind of question about your purchase.
