i Board IB-P054C Black Running Boards Style Installation Guide

June 1, 2024
i Board

i Board IB-P054C Black Running Boards Style Installation Guide
i Board IB-P054C Black Running Boards Style

READ INSTRUCTIONS CAREFULLY BEFORE START ING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED.

*ROCKER PANEL MOUNT*
DRILLING IS REQUIRED**

Fastener Size Tightening Torque (ft-lbs) Required
6mm 6-7
8mm 16-18
10mm 31-32 X
12mm 56-58 X
14mm 92-94 X

PART LIST

Parts List

Hardware Package A (For Bracket Installation)

Item| QTY| Description| Item| QTY| Description
1#| 6| Mounting Brackets| 4#| 6| M8 Nylon Lock Nuts
2#| 6| M8X1.25-20mm Hex Bolts| 5#| 12| ST6.3-22mm Hex Flange Self Tapping Screws
3#| 12| M8 Flat Washers| | |
Hardware Package
Hardware Package B (For Step Bar Installation)

Item| QTY| Description| Item| QTY| Description
1#| 12| M8X1.25-35mm Carriage Bolts| 3#| 12| M8 Nylon Lock Nuts
2#| 12| M8 Large Flat Washers| 4#| 6| Sliders (Packed with Mounting Brackets)
Hardware Package

STEP 1

Starting on the Driver side of the vehicle. Drilling (3) 8mm holes in pinch weld as shown (Fig 1).

(Fig 1) Driver Side Mounting Locations
Driver Side Mounting Locations

STEP 2

Select (1) Mounting Bracket, attach the Mounting Bracket to the drilled holes on driver side front mounting location.

Use the bracket as a template, mark and drill the upper two 5mm holes on the rocker panel.

Secure the upper mounting holes of the bracket to the rocker panel with (2) ST6.3-22mm Hex Flange Self Tapping Screws.

And attach the lower mounting hole to the pinch weld with (1) M8X1.25-20mm Hex Bolts, (2) M8 Flat Washers and (1) M8 Nylon Lock Nuts (Fig 2). Do not fully tighten at this time.

(Fig 2) Driver Front Mounting Bracket Installation
Driver Front Mounting

STEP 3

Repeat Steps 1-2 for the other Mounting Brackets installation.
Do not fully tighten hardware at this time.

Note : (6) Mounting Brackets are Universal.

STEP 4

Once all (3) Driver side mounting brackets are installed, then proceed to the Step Bar installation. (Figs 3 & 4).

  1. Select (1) Slider and (2) M8X1.25-35mm Carriage Bolts;
  2. Install (2) M8X1.25-35mm Carriage Bolts in (1) Slider.
  3. Slide the Slider (with carriage bolts) to the Step Bar.
  4. Repeat to install the other (2) sliders to the step bar.
  5. Attach the Step Bar (with the Sliders) onto the installed mounting brackets. Position the Sliders to the installed brackets. Secure the Step Bar to the installed Brackets by using (6) M8 Large Flat Washers and
  6. M8 Nylon Lock Nuts and (3) Sliders, (Fig 4). Do not fully tighten hardware at this time.

Note: The Sliders are packed with the Mounting Brackets.

Level and adjust the Step Bar and fully tighten all hardware.

Repeat Steps 1-4 for the other side Step Bar installation.
The installation is completed!!!

Attention
Do periodic inspections to the installation to make sure that all hardware is secure and tight.

In order to protect your bars/boards, please use mild soap/non-abrasive products for cleaning only.

(Fig 3) Slider Installation
Slider Installation

(Fig 4) Step Bar Installation
Step Bar Installation

Customer Support: info@iboardauto.com

Scan for Installation Video
QR Code

i Board Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

i Board User Manuals

Related Manuals