i Board IB-064C&H Black 6 Inch Stainless Steel Running Boards Nerf Bars Side Steps Installation Guide
- June 1, 2024
- i Board
Table of Contents
i Board IB-064C&H Black 6 Inch Stainless Steel Running Boards Nerf Bars
Side Steps
READ INSTRUCTIONS CAREFULLY BEFORE START ING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED.
- BODY FRAME MOUNT
- NO DRILLING REQUIRED
PART LIST
| Fastener Size | Tightening Torque (ft-lbs) | Required |
|---|---|---|
| 6mm | 6-7 | √ |
| 8mm | 16-18 | √ |
| 10mm | 31-32 | √ |
| 12mm | 56-58 | √ |
| 14mm | 92-94 | X |
Hardware Package A (For Bracket Installation)
| Item | QTY | Description | Item | QTY | Description |
|---|---|---|---|---|---|
| 1# | 6 | M10X1.5-30mm Hex Bolts | 8# | 2 | M8X1.25-25mm Hex Bolts |
| 2# | 12 | M10 Large Flat Washers | 9# | 4 | M8 Large Flat Washers |
| 3# | 6 | M10 Lock Washers | 10# | 2 | M8 Nylon Lock Nuts |
| 4# | 6 | M10 Hex Nuts | 11# | 2 | M6X1-30mm Hex Bolts |
| 5# | 2 | M12X1.75-100mm Hex Bolts | 12# | 4 | M6 Flat Washers |
| 6# | 4 | M12 Large Flat Washers | 13# | 2 | M6X1 Nylon Lock Nuts |
| 7# | 2 | M12 Nylon Lock Nuts |
Hardware Package B (For Stainless Steel Step Bar Installation)
Hardware Package B (For Stainless Steel Step Bar Installation)
Item| QTY| Description| Item| QTY| Description
1#| 8| M8X1.25-35mm Carriage Bolts| 3#| 8| M8 Nylon Lock Nuts
2#| 8| M8 Large Flat Washers| 4#| 4| Sliders (Packed with Step Bars)
Installation
- STEP 1 Start installing from the passenger side front of the vehicle. Remove the passenger front body mount bolt.
- STEP 2 Assemble Passenger Front Mounting Bracket (PFM) and Passenger Front Support Bracket (DFS/PFS) with (2) M10X1.5-30mm Hex Bolts, (4) M10 Large Flat Washers, (2) M10 Lock Washers and (2) M10 Hex Nuts, (Fig 1). Do not fully tighten hardware at this time.
- STEP 3
Attach the assembled Passenger Front Mounting Bracket (PFM) to the vehicle with factory bolt, (Fig 2 & 3).
Attach Passenger Front Support Bracket (DFS/PFS) to smaller factory hole in the frame using (1) M12X1.75-100mm Hex Bolt, (1) M12 Nylon Lock Nut, (2) M12 Large Flat Washers, (Fig 2 & 3). Do not fully tighten hardware at this time.
- STEP 4 Move to the passenger side rear mounting location. Remove the passenger rear body mount bolt.
- STEP 5 Assemble Passenger Rear Mounting Bracket (PRM) and Passenger Rear Support Bracket (PRS) with (1) M10X1.5-30mm Hex Bolt, (2) M10 Large Flat Washers, (1) M10 Lock Washer and (1) M10 Hex Nut, (Fig 3). Do not fully tighten hardware at this time.
STEP 6
Attach the assembled Passenger Rear Mounting Bracket (PRM) to the vehicle with
factory bolts, (Fig 4 & 5).
Attach Passenger Rear Support Bracket (PRS) to the factory hole on the inner
side of body mount cavity and closer to the frame using:
05-07 Models:
(1) M8X1.25-25mm Hex Bolt, (1) M8 Nylon Lock Nut, (2) M8 Large Flat Washers
(Fig 4). Do not fully tighten hardware at this time.
08-On Models:
(1) M6X1-30mm Hex Bolt, (1) M6 Nylon Lock Nut, (2) M6 Flat Washers (Fig 5). Do
not fully tighten hardware at this time.
STEP 7
Once all (2) Passenger side mounting brackets are installed, then proceed to
the Step Bar installation. (Figs 6 & 7)
- Select (1) Slider and (2) M8X1.25-35mm Carriage Bolts;
- Install (2) M8X1.25-35mm Carriage Bolts in (1) Slider.
- Slide the Slider (with carriage bolts) to the Step Bar.
- Repeat to install the other (1) slider to the step bar.
- Attach the Step Bar (with the Sliders) onto the installed mounting brackets. Position the Sliders to the installed brack-ets. Secure the Step Bar to the installed Brackets by using (4) M8 Large Flat Washers and (4) M8 Nylon Lock Nuts and (2) Sliders, (Fig 7). Do not fully tighten hardware at this time.
Note : The Sliders are packed with the Step Bars.
Level and adjust the Step Bar and fully tighten all hardware.
Repeat Steps 1-7 for the other side Step Bar installation. The installation is
completed!!!
Attention
Do periodic inspections to the installation to make sure that all hardware is
secure and tight.
In order to protect your bars/boards, please use mild soap/non-abrasive
products for cleaning only.
Customer Support : info@iboardauto.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>