i Board IB-021C&H Stainless Steel Polished Silver Running Boards Installation Guide

June 1, 2024
i Board

IB-021C &H Stainless Steel Polished
Silver Running Boards
Installation Guide

i Board IB 021C&H Stainless Steel Polished Silver Running
Boards PART#: IB-021C &H
iBoard ® by APS

IB-021C&H Stainless Steel Polished Silver Running Boards

READ INSTRUCTIONS CAREFULLY BEFORE START ING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED.
ROCKER PANEL MOUNT
NO DRILLING REQUIRED

Fastener Size Tightening Torque (ft-lbs) Required
6mm 7-Jun X
8mm 16-18
10mm 31-32 X
12mm 56-58 X
14mm 92-94 X

i Board IB 021C&H Stainless Steel Polished Silver Running Boards - PART
LIST

Hardware Package A (For Bracket Installation)

Item| QTY| Description| Item| QTY| Description
1#| 6| M8 U-Bolts| 4#| 24| M8 Lock Washers
2#| 12| M8X1.25-40mm Hex Bolts| 5#| 24| M8 Hex Nuts
3#| 36| M8 Large Flat Washers| | |

i Board IB 021C&H Stainless Steel Polished Silver Running Boards - Hardware
Package

Hardware Package B (For Stainless Steel Step Bar Installation)

Item| QTY| Description| Item| QTY| Description
1#| 12| M8X1.25-35mm Carriage Bolts| 3#| 12| M8 Nylon Lock Nuts
2#| 12| M8 Large Flat Washers| 4#| 6| Sliders (Packed with Step Bars)

i Board IB 021C&H Stainless Steel Polished Silver Running Boards - Hardware
Package1

STEP 1
On the driver side of the vehicle, locate the (2) factory holes above rubber grommets on the side panel on the front, center and rear mounting locations, (Fig 1).
STEP 2
Start the installation from the driver side front. Select (1) M8 UBolt.
Insert the short end of the M8 U-Bolt into one of the  factory holes and out from the opposite hole (Fig 2).i Board IB 021C&H Stainless Steel Polished
Silver Running Boards - Hardware Package2

STEP 3
Attach the Driver Front Mounting Bracket (DFM/DCM) to the installed M8 U- Bolt with (2) M8 Lock Washer, (2) M8 Large Flat Washers and (2) M8 Hex Nuts, (Fig 3). Do not fully tighten hardware at this time.
NOTE: Hold the U-Bolt in place and line up the threaded ends with the slots in the Mounting Bracket carefully. Do not let the U -Bolt fall into the body panel within installing.

STEP 4
Position (1) Support Bracket on the pinch weld and line up with the Driver Front Mounting Bracket , (Fig 4). Attach the Support Bracket to the Mounting Bracket with (2) M8X1.25-40mm Hex Bolts, (4) M8 Large Flat Washers, (2) M8 Lock Washers, and (2) M8 Hex Nuts, (Fig 5-7). Do not fully tighten hardware at this time.
NOTE: Mount the Support Bracket with the concave facing the inside of the vehicle, (Fig 4).i Board IB 021C&H Stainless Steel Polished Silver Running
Boards - Hardware Package4

STEP 5
Move to the driver side center & rear mounting locations of the vehicle. Repeat Steps 1-4 for Driver Center Mounting Bracket (DFM/DCM) & Driver Rear Mounting Bracket (DRM) installation, (Fig 6 & 7). Do not fully tighten hardware  at this time. i Board IB 021C&H Stainless Steel Polished
Silver Running Boards - Hardware Package5

STEP 6
Once all (3) Driver side mounting brackets are installed, then proceed to the Step Bar installation. (Figs 8 & 9) (1) Select (1) Slider and (2) M8X1.25-35mm Carriage Bolts; (2) Install (2) M8X1.25-35mm Carriage Bolts in (1) Slider. (3) Slide the Slider (with carriage bolts) to the Step Bar. (4) Repeat to install the other (2) sliders to the step bar. (5) Attach the Step Bar (with the Sliders) onto the installed mounting brackets. Position the Sliders to the installed brackets. Secure the Step Bar to the installed Brackets by using (6) M8 Large Flat Washers and (6) M8 Nylon Lock Nuts   and   (3) Sliders, (Fig 9). Do not  fully tighten hardware at this time.
Note: The Sliders are packed with the Step Bars.
Level and adjust the Step Bar and fully tighten all hardware.
Repeat Steps 1-6 for the other side Step Bar installation. T he installation is completed!!!i Board IB 021C&H Stainless Steel Polished
Silver Running Boards - Slider

Attention
Do periodic inspections to the installation to make sure that all hardware is secure and tight.
In order to protect your bars/boards, please use mild soap/non-abrasive products for cleaning only.

https://www.iboardauto.com/iboard-videos/

Customer Support: info@iboardauto.com 
Rev. 20230901

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

i Board User Manuals

Related Manuals