i Board IB-202C Running Board 4 Black Installation Guide
- June 1, 2024
- i Board
Table of Contents
iBoard® by APS
PART#: IB-202C &H
https://www.iboardauto.com/iboard-videos/
IB-202C Running Board 4 Black
READ INSTRUCTIONS CAREFULLY BEFORE START ING INSTALLATION. REMOVE CONTENTS
FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED.
ROCKER PANEL MOUNT
NO DRILLING REQUIRED
| Fastener Size | Tightening Torque (ft-lbs) | Required |
|---|---|---|
| 6mm | 6-7 | X |
| 8mm | 16-18 | √ |
| 10mm | 31-32 | √ |
| 12mm | 56-58 | X |
| 14mm | 92-94 | X |
PART LIST
Hardware Package A (For Bracket Installation)
| Item | QTY | Description |
|---|---|---|
| 1# | 6 | M10X45 Bolt Plates |
| 2# | 2 | M10X30 Handle Bolt Plates |
| 3# | 2 | M10X1.5-35mm Hex Bolts |
| 4# | 12 | M10 Large Flat Washers |
| 5# | 10 | M10 Lock Washers |
| 6# | 10 | M10 Hex Nuts |
Hardware Package B (For Stainless Steel Step Bar Installation)
| Item | QTY | Description |
|---|---|---|
| 1# | 8 | M8X1.25-35mm Carriage Bolts |
| 2# | 8 | M8 Large Flat Washers |
| 3# | 8 | M8 Nylon Lock Nuts |
| 4# | 4 | Sliders (Packed with Step Bars) |
STEP 1 Start installation from the driver side front of the vehicle,
locate the (2) factory holes in the lateral floor panel support by the front
tires. Insert (1) M10X45 Bolt Plate into each of the factory holes.
IMPORTANT! Once you have inserted the Bolt Plates, make sure that the
welded washer on each Bolt Plate is in the center of the factory hole, (Fig
1).
(Fig 1) M10X45 Bolt Plate Installation (on Driver Side Front Mounting Location)
STEP 2 Select the Driver Front Mounting Bracket (DFM) and attach it to
the installed M10X45 Bolt Plates using (2) M10 Large Flat Washers, (2) M10
Lock Washers and (2) M10 Hex Nuts, (Fig 2). Do not fully tighten hardware at
this time.
NOTE: When tightening the Bolt Plates, make sure that they are fully
engaged at all times.
(Fig 2) Driver Front Mounting Bracket Installed (example)
STEP 3 Move to the driver side rear of the vehicle. There are (2) large
factory holes by the rear of the floor panel, one in the lateral floor panel
support and one in the horizontal floor panel support. Insert (1) M10X45 Bolt
Plate into factory hole in the lateral floor panel support, (Fig 3).
IMPORTANT! Once you have inserted the Bolt Plate, make sure that the
welded washer on the Bolt Plate is in the center of the factory hole.
(Fig 3) M10X45 Bolt Plate Installed (Driver Side Rear)
STEP 4 Attach Driver Rear Mounting Bracket (DRM) to installed M10X45 Bolt
Plate using (1) M10 Large Flat Washer, (1) M10 Lock Washer and (1) M10 Hex
Nut, (Fig 6). Do not fully tighten hardware at this time.
NOTE: When tightening the Bolt Plate, make sure is fully engage at all
times.
STEP 5 To the right side of the Driver Rear Mounting Bracket, there is
one oval factory hole and one round factory hole in the floor panel. Insert
(1) M10X30 Handle Bolt Plate through inside oval factory hole so Bolt drops
through outside round hole, (Figs 4 & 5).
Attach Driver Rear Support Bracket (DRS) to already inserted M10X30 Handle
Bolt Plate using the included (1) M10 Large Flat Washer, (1) M10 Lock Washer
and (1) M10 Hex Nut, (Fig 6). Do not fully tighten hardware at this time.
(Fig 4) M10X30 Handle Bolt Plate Installation
(Fig 5) M10X30 Handle Bolt Plate Installed
STEP 6 Attach opposite side of Support Bracket to Driver Rear Mounting Bracket using the included (1) M10X1.5-35 Hex Bolt, (2) M10 Large Flat Washers, (1) M10 Lock Washer and (1) M10 Hex Nut, (Fig 6). Do not fully tighten hardware at this time.
(Fig 6) Driver Rear Mounting Bracket Installation
STEP 7
Once all (2) Driver side mounting brackets are installed, then proceed to the
Step Bar installation. (Figs 7 & 8)
- Select (1) Slider and (2) M8X1.25-35mm Carriage Bolts;
- Install (2) M8X1.25-35mm Carriage Bolts in (1) Slider.
- Slide the Slider (with carriage bolts) to the Step Bar.
- Repeat to install the other (1) slider to the step bar.
- Attach the Step Bar (with the Sliders) onto the installed mounting brackets. Position the Sliders to the installed brackets. Secure the Step Bar to the installed Brackets by using (4) M8 Large Flat Washers and (4) M8 Nylon Lock Nuts and (2) Sliders, (Fig 8). Do not fully tighten hardware at this time. Note: The Sliders are packed with the Step Bars. Level and adjust the Step Bar and fully tighten all hardware. Repeat Steps 1-7 for the other side Step Bar installation. The installation is completed!!!
Attention
Do periodic inspections to the installation to make sure that all hardware is
secure and tight.
In order to protect your bars/boards, please use mild soap/non-abrasive
products for cleaning only.
Customer Support: info@iboardauto.com
Rev. 20230501
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>