i Board IB-134C&H Polished Silver Stainless Steel Running Boards Instruction Manual

June 1, 2024
i Board

i-Board-LOGO

i Board IB-134C&H Polished Silver Stainless Steel Running Boards

i-Board-IB-134C&H-Polished-Silver-Stainless-Steel-Running-Boards-
PRODUCT

Product Information

Specifications

  • Product Name: Rocker Panel Mount Step Bar
  • Part Number: IB-134C&H
  • No drilling required

Parts List

Mounting Bracket List

  • Driver & Passenger Front Mounting Brackets – 2 pieces
  • Passenger Center & Rear Mounting Brackets – 3 pieces
  • Driver Center & Rear Mounting Brackets – 2 pieces

Hardware Package A (For Bracket Installation)

  • M8X1.25-25mm Hex Bolts – 12 pieces
  • M8 Hex Nuts – 6 pieces
  • M8 Large Flat Washers – 18 pieces
  • ST8x25mm Hex Self Tapping Screws – 6 pieces
  • M8 Lock Washers – 12 pieces

Hardware Package B (For Stainless Steel Step Bar Installation)

  • M8X1.25-35mm Carriage Bolts – 12 pieces
  • M8 Nylon Lock Nuts – 12 pieces
  • M8 Large Flat Washers – 12 pieces
  • Sliders (Packed with Step Bars) – 6 pieces

Product Usage Instructions

  1. Step 1: Install all passenger side mounting brackets.
  2. Step 2: Install the sliders and step bars using the provided hardware as per instructions.

Note: Follow the detailed installation steps provided in the manual for proper assembly and attachment of the step bars.

Frequently Asked Questions (FAQ)

  • Q: Is drilling required for installing the Rocker Panel Mount Step Bar?
    A: No, drilling is not required for installation. The step bars can be mounted without drilling.

  • Q: How many sliders are included in the package?
    A: The package includes 6 sliders which are packed with the step bars for installation.

iBoard® by APS
READ INSTRUCTIONS CAREFULLY BEFORE START ING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED.

  • ROCKER PANEL MOUNT
  • NO DRILLING REQUIRED

PART#: IB-134C&H

PART LIST

i-Board-IB-134C&H-Polished-Silver-Stainless-Steel-Running-Boards-
\(2\)

Mounting Bracket List ****

Item| QTY| Description| Item| QTY| Description
1#| 2| Driver & Passenger Front Mounting Brackets| 3#| 2| Passenger Center & Rear Mounting Brackets
2#| 2| Driver Center & Rear Mounting Brackets| | |
Hardware Package A (For Bracket Installation)

Item| QTY| Description| Item| QTY| Description
1#| 12| M8X1.25-25mm Hex Bolts| 4#| 6| M8 Hex Nuts
2#| 18| M8 Large Flat Washers| 5#| 6| ST8x25mm Hex Self Tapping Screws
3#| 12| M8 Lock Washers| | |
i-Board-IB-134C&H-Polished-Silver-Stainless-Steel-Running-Boards-
\(3\)
Hardware Package B (For Stainless Steel Step Bar Installation)

Item| QTY| Description| Item| QTY| Description
1#| 12| M8X1.25-35mm Carriage Bolts| 3#| 12| M8 Nylon Lock Nuts
2#| 12| M8 Large Flat Washers| 4#| 6| Sliders (Packed with Step Bars)
i-Board-IB-134C&H-Polished-Silver-Stainless-Steel-Running-Boards-
\(4\)

STEP 1
Start installation from the Passenger Side of the vehicle. Identi-fy the mounting locations along the inner side of the rocker pan-el, remove any tape on the inside of rocker panel that covers the mounting holes, (Fig 1).

NOTE: (1) ST8x25mm Hex Self Tapping Screws replace (1) M8X1.25-25mm Hex Bolt per bracket if the factory holes are not tapped for 8mm bolts, (Fig 1).
Attach the passenger side mounting brackets to underside of the rocker panel as shown on Fig 1. Do not fully tighten hard-ware at this time.

STEP 2
Once all (3) Passenger side mounting brackets are installed, then proceed to the Step Bar installation. (Figs 2 & 3)

  1. Select (1) Slider and (2) M8X1.25-35mm Carriage Bolts;
  2. Install (2) M8X1.25-35mm Carriage Bolts in (1) Slider.
  3. Slide the Slider (with carriage bolts) to the Step Bar.
  4. Repeat to install the other (2) sliders to the step bar.
  5. Attach the Step Bar (with the Sliders) onto the installed mounting brackets. Position the Sliders to the installed brack-ets. Secure the Step Bar to the installed Brackets by using (6) M8 Large Flat Washers and (6) M8 Nylon Lock Nuts and (3) Sliders, (Fig 3). Do not fully tighten hardware at this time.

Note: The Sliders are packed with the Step Bars.
Level and adjust the Step Bar and fully tighten all hardware.
Repeat Steps 1-2 for the other side Step Bar installation. The installation is completed!!!

i-Board-IB-134C&H-Polished-Silver-Stainless-Steel-Running-Boards-
\(5\)

i-Board-IB-134C&H-Polished-Silver-Stainless-Steel-Running-Boards-
\(6\)

Customer Support: info@iboardauto.com
Rev. 20230401

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

i Board User Manuals

Related Manuals