i Board IB-P003C 6 Inch Aluminum Running Boards Nerf Bars Instruction Manual

June 1, 2024
i Board

i Board IB-P003C 6 Inch Aluminum Running Boards Nerf Bars Instruction Manual
i Board IB-P003C 6 Inch Aluminum Running Boards Nerf
Bars

READ INSTRUCTIONS CAREFULLY BEFORE START ING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED

*ROCKER PANEL MOUNT*
NO DRILLING REQUIRED**

Fastener Size Tightening Torque (ft-lbs) Required
6mm 6-7 X
8mm 16-18
10mm 31-32 X
12mm 56-58 X
14mm 92-94 X

PART LIST

Front

Driver Side Step Bar
Part List

Passenger Side Step Bar
Part List

Hardware Package A (For Bracket Installation)

Item| QTY| Description| Item| QTY| Description
1#| 6| Mounting Brackets| 4#| 12| M8 Lock Washers
2#| 24| M8X1.25-25mm Hex Bolts| 5#| 12| M8 Nylon Lock Nuts
3#| 36| M8 Large Flat Washers| 6#| 12| M8 Clip Nuts
**2 #

3 #

4 #
Hardware Package
5 #


Hardware Package B (For Step Bar Installation)**

Item| QTY| Description| Item| QTY| Description
1#| 12| M8X1.25-35mm Carriage Bolts| 3#| 12| M8 Nylon Lock Nuts
2#| 12| M8 Large Flat Washers| 4#| 6| Sliders (Packed with Mounting Brackets)
1 #

**2 #

3 #

4 #**

STEP 1

Start installation from the passenger side of the vehicle, locate the (3) pairs of factory holes along the pinch weld (Figs 1 & 2).
Assembly Instruction
(Fig 1) Passenger Side Pinch Weld Mounting Location

NOTE: There are (4) mounting locations along the inner body panel. Running Board installation will use the 2nd,3rd and 4th mounting locations, (Figs 1 & 2).
Assembly Instruction
(Fig 2) Passenger Side Front Mounting Locations

STEP 2

Select (2) M10 Clip Nuts. Insert Clip Nuts into the rectangular opening. Line up the threaded hole on the clip nuts with the round hole next to the rectangular opening.
NOTE: The threaded nut on the Clip Nut must go towards the inside of the side panel, (Figs 3 & 4).
Assembly Instruction
(Fig 3) Typical Mounting Location
Assembly Instruction
(Fig 4) M10 Clip Nut Installed

STEP 3

Attach the Passenger Front Mounting Bracket to the installed M10 Clip Nuts with (2) M10X1.5-30 Hex Bolts, (2) M10 Lock Washers, (2) M10 Large Flat Washers; and secure (2) lower holes with (2) M10X1.5-30 Hex Bolts, (4) M10 Large Flat Washers (2) M10 Nylon Lock Nuts, (Fig 5). Do not fully tighten hard ware at this time.
Assembly Instruction
(Fig 5) Passenger Front Mounting Bracket Installation

STEP 4

Move to the Passenger Side Center & Rear Mounting Locations. Repeat Steps 1-3 to attach the Mounting Brackets to the vehicle. Do not fully tighten hardware at this time. (Fig 6)
Assembly Instruction
(Fig 6) Passenger Rear Mounting Bracket Installation

STEP 5

Once all (3) Passenger side mounting brackets are installed, then proceed to the Step Bar installation. (Figs 7 & 8)

  1. Select (1) Slider and (2) M8X1.25-35mm Carriage Bolts;
  2. Install (2) M8X1.25-35mm Carriage Bolts in (1) Slider.
  3. Slide the Slider (with carriage bolts) to the Step Bar.
  4. Repeat to install the other (2) sliders to the step bar.
  5. Attach the Step Bar (with the Sliders) onto the installed mounting brackets. Position the Sliders to the installed brackets. Secure the Step Bar to the installed Brackets by using (6) M8 Large Flat Washers and (6) M8 Nylon Lock Nuts and (3) Sliders, (Fig 8). Do not fully tighten hardware at this time.

Note: The Sliders are packed with the Mounting Brackets. Level and adjust the Step Bar and fully tighten all hardware. Repeat Steps 1-5 for the other side Step Bar installation. The installation is completed!!!

Attention
Do periodic inspections to the installation to make sure that all hardware is secure and tight. In order to protect your bars/boards, please use mild soap /non-abrasive products for cleaning only.

Assembly Instruction
(Fig 7) Slider Installation
Assembly Instruction
(Fig 8) Step Bar Installation

Customer Support: info@iboardauto.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

i Board User Manuals

Related Manuals