i Board IB-027C Running Boards Nerf Bars Side Steps Instruction Manual

: June 1, 2024
: i Board

Table of Contents

i Board IB-027C Running Boards Nerf Bars Side Steps
PART LIST
Mounting Bracket List
STEP 1
STEP 2
STEP 3
Read User Manual Online (PDF format)
Download This Manual (PDF format)

i Board IB-027C Running Boards Nerf Bars Side Steps

i Board-IB-027C-Running-Boards-Nerf-Bars-Side-Steps-
product

READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM THE BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED.

ROCKER PANEL MOUNT
NO DRILLING REQUIRED $i Board-IB-027C-Running-Boards-Nerf-Bars-Side-Steps-fig- $1$$

PART LIST

$i Board-IB-027C-Running-Boards-Nerf-Bars-Side-Steps-fig- $2$$

Mounting Bracket List

$i Board-IB-027C-Running-Boards-Nerf-Bars-Side- Steps-fig- $3$$

Hardware Package A (For Bracket Installation) $i Board-IB-027C-Running-Boards-Nerf-Bars-Side-Steps-fig- $4$$
Hardware Package B (For Stainless Steel Step Bar Installation) $i Board-IB-027C-Running-Boards-Nerf-Bars-Side-Steps-fig- $5$$

STEP 1

Start installation from the driver-side front of the vehicle. Locate on the backside of the rocker panel (3) mounting holes where the plastic fascia is cut out. Select (2) M8 Clip Nuts, and line up the Clip Nuts with the holes. Locate a threaded hole above the clip nuts on the rocker panel. If equipped, remove the plug to expose the threaded hole.
NOTE: Threaded nut on Clip nut must face inside of the side panel, (Fig 1).

STEP 2

Attach the assembled Driver Front Bracket to the installed M8 Clip Nuts with the included (2) M8X1.25-30mm Hex Bolts, (2) M8 Lock Washers and (2) M8 Large Flat Washers; to the threaded hole using (1) M8X1.25-30mm Hex Bolt, (1) M8 Lock Washers and (1) M8 Large Flat Washer, (Fig 2). Do not fully tighten at this time.

STEP 3

Move to the driver-side rear mounting location. Repeat Steps 1—2 to install (1) Driver Rear Mounting Bracket, (Fig 3). Do not fully tighten the hardware at this time.

STEP 4
Once all (2) Driver side mounting brackets are installed, then proceed to the Step Bar installation. (Figs 4 & 5)

$i Board-IB-027C-Running-Boards-Nerf-Bars-Side-Steps-fig- $9$$

Select (1) Slider and (2) M8X1.25-35mm Carriage Bolts;
Install (2) M8X1.25-35mm Carriage Bolts in (1) Slider.
Slide the Slider (with carriage bolts) to the Step Bar.
Repeat to install the other (1) slider to the step bar.
Attach the Step Bar (with the Sliders) to the installed mounting brackets.
Position the Sliders to the installed brackets. Secure the Step Bar to the installed Brackets by using (4) M8 Large Flat Washers (4) M8 Nylon Lock Nuts and (2) Sliders, (Fig 5). Do not fully tighten the hardware at this time.
Note: The Sliders are packed with the Step Bars. Level and adjust the Step Bar and fully tighten all hardware. Repeat Steps 1-4 for the other side Step Bar installation. The installation is completed!!!

Attention

Do periodic inspections of the installation to make sure that all hardware is secure and tight.
To protect your bars/boards, please use mild soap/non-abrasive products for cleaning only.