i Board IB-R414 Running Board 6 Silver Instruction Manual
- June 1, 2024
- i Board
Table of Contents
i Board IB-R414 Running Board 6 Silver
Product Information
Specifications
- Part Number: IB-R414
- Mounting Type: Rocker Panel Mount
- Fastener Sizes: 6mm, 8mm, 10mm, 12mm, 14mm
- Tightening Torque (ft-lbs): 6-7, 16-18, 31-32, 56-58, 92-94
Product Usage Instructions
Part List
- Driver Front Mounting Bracket (DFM)
- Passenger Front Mounting Bracket (PFM)
- Passenger Center Mounting Bracket (PCM)
- Driver Rear Mounting Bracket (DRM)
- Passenger Center Mounting Bracket 1 (PCM1)
- Passenger Rear Mounting Bracket (PRM)
Hardware Package A (For Bracket Installation)
Includes various bolts, washers, nuts, and installation tools for bracket installation.
Hardware Package B (For Step Bar Installation)
Includes square head bolts, lock nuts, and large flat washers for step bar installation.
Installation Steps
- Step 1: Starting installation from the driver side front of the vehicle.
- Step 2: Select the Driver Front Mounting Bracket (DFM) and attach it to the installed Bolt Plate.
- Step 3: Line up the mounting tab on the Bracket with the factory hole in the pinch weld and drill if necessary.
- Step 4: Attach the lower mounting hole on the Bracket to the Clip Nut with the provided hardware.
Frequently Asked Questions
Q: Is drilling required for installation?
A: Yes, drilling is required for proper installation. Follow the provided instructions carefully.
Q: What should I do if any parts are missing from the box?
A: Contact customer support at info@iboardauto.com for assistance in obtaining the missing parts.
Q: How can I ensure a secure installation?
A: Follow the specified tightening torque values for different fastener sizes to ensure a secure and safe installation.
PART#: IB-R414
READ INSTRUCTIONS CAREFULLY BEFORE START ING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRE-SENT. ASSISTANCE IS RECOMMENDED.
- ROCKER PANEL MOUNT
- DRILLING IS REQUIRED
Fastener Size | Tightening Torque (ft-lbs) | Required |
---|---|---|
6mm | 6-7 | √ |
8mm | 16-18 | √ |
10mm | 31-32 | √ |
12mm | 56-58 | X |
14mm | 92-94 | X |
PART LIST
Hardware Package A
(For Bracket Installation)
INSTALLATION
- STEP 1
Starting installation from the driver side front of the vehicle. Lo-cate and remove the rubber plug near the front tire opening,
(Fig 1). Select (1) M10X35 Bolt Plate, (Fig 2). Insert the Bolt Plate into and across the opening, (Fig 3).
- STEP 2
Select the Driver Front Mounting Bracket (DFM). Attach the Bracket to the installed M10X35 Bolt Plate with (1) M10 Large Flat Washer, (1) M10 Lock Washer and (1) M10 Hex Nut, (Fig 4). Do not fully tighten hardware at this time.
-
STEP 3
Line up the mounting tab on the Bracket with the factory hole in the pinch weld. Slide (1) M8 Clip Nut over the hole in the pinch weld with the nut toward the outside of the vehicle, (Fig 3).
Note: On some models, 5/16” holes may require to drill on the pinch weld to attach the Mounting Bracket.- a. Line up the tab on the Bracket with a flat area on the back of the pinch weld.
- b. Fully tighten the M10 Hex Nut on the M10X35 Bolt Plate. Use the tab on the Bracket for a guide and drill a 5/16” hole through the tab and the pinch weld. MPORTANT!Any cutting or drilling tool may break or shatter. Gov-ernment regulations require safety glasses & equip-ment at all times when cutting or drilling.
- c. Slide (1) M8 Clip Nut over the drilled hole in the pinch weld with the nut toward the outside.
-
STEP 4
Attach the lower mounting hole on the Bracket to the M8 Clip Nut with (1) M8X1.25-25mm Hex Bolt, (1) M8 Lock Washer and (1) M8 Large Flat Washer, (Fig 4). Do not fully tighten the hard-ware.
- STEP 5
Move to the driver side rear of the vehicle, (Fig 6). Locate and remove the large oval rubber plug. Insert (1) M10X40 Bolt Plate into the opening, (Figs 5 & 6).
Attach the Driver Rear Mounting Bracket (DRM) to the M10X40 Bolt Plate with (1) M10 Large Flat Washer, (1) M10 Lock Washer and (1) M10 Hex Nut, (Fig 7). Repeat Steps 3 & 4 to attach the Mounting Bracket to the back of the pinch weld (Fig 7).
- STEP 6
Once all (2) mounting brackets are installed. Select the Driver Side Running Board (the short one). Slip (2) M6X1-20mm Square Head Bolts into each bottom channel (Fig 8). Carefully position the Running Board onto the (2) Mounting Brackets. Attach the Running Board to each Mounting Bracket with (2) M6X1-20mm Square Head Bolts, (2) M6 Large Flat Washers and (2) M6X1 Nylon Lock Nuts, (Fig 9). Do not fully tighten hardware at this time.
IMPORTANT: Do not slide the Running Board on the Brackets or the bottom surface of the board will be damaged.
Level and adjust the Running Board and fully tighten all hard-ware.
- STEP 7
Move to the passenger side of the vehicle.
Start installation from the passenger side front of the vehicle,
(Fig 10). Repeat Steps 1—4 to install the Passenger Front Mounting Bracket (PFM), (Fig 11). Do not fully tighten hardware at this time.
- STEP 8
Move to the 2nd Mounting Bracket location, (Fig 12). Repeat Step 5 to install the Passenger Center Mounting Bracket (PCM), (Figs 12 & 13). Do not fully tighten hardware at this time.
-
STEP 9
Move to the 3rd Bracket location below the siding door, (Fig 14). Determine the correct procedure for your year/model for the remaining (2) passenger side Brackets:
Models with factory holes in pinch weld and inner body panel:-
a. Locate the factory hole in the pinch weld. Also locate the square hole and small round hole in the inner body panel near and above the hole in the pinch weld, (Fig 14). NOTE: Hold the appropriate Mounting Bracket up in each location to help determine the correct holes to use.
-
b. Slide (1) M8 Clip Nut into the square hole and in line with the smaller round hole. Next, slide (1) M8 Clip Nut over the hole through the pinch weld as described in Step 3,
(Fig 14). -
c. Select the Passenger Center Mounting Bracket 1 (PCM1). Attach the Bracket to the (2) M8 Clip Nuts with (2) M8X1.25-25mm Hex Bolts, (2) M8 Lock Washers and (2) M8 Large Flat Washers, (Fig 15). Do not fully tighten hardware at this time.
-
d. Move to 4th mounting bracket locations Repeat Steps a—c to install the Passenger Rear Mounting Bracket (PRM),(Figs 16-17).
-
Models without factory holes in the pinch weld and/or inner body panel
- a. Repeat Step 7 to attach the Running Board to the front and 2nd Mounting Brackets.
- b. Use a stand or a jack to hold the Running Board up and level with the front (2) Brackets.
- c. Select the 3rd Passenger Center Mounting Bracket 1 (PCM1). With the Running Board level to the vehicle, hold the Bracket up in position against the back of the pinch weld and body panel. Mark the location of the slots in the Bracket onto the sheet metal, (Fig 18). NOTE: Use a clamp or locking pliers to temporarily attach the Bracket to the pinch weld.
- d. Drill a 7/16” hole in the center of the mark for the top mounting tab, (Fig 18). IMPORTANT: Make sure the Run-ning Board is level to the vehicle before drilling any mounting holes.
- e. Select (1) M8 Insert Installation Tool, (1) M8X1.25-40mm Hex Bolt, (1) M8 Large Flat Washer and (1) M8 Rivet Nut. Assemble the Insert as pictured in Fig 19 . NOTE: Select 8 mm hole on Insert Installation Tool (Fig 20).
- f. Firmly hold the handle and push the Rivet Nut into the hole. Use a small hammer to gently tap the insert into the hole if necessary. Once inserted, hold the handle with one hand and turn the M8 Hex Bolt, (tighten), with a wrench to expand the Rivet Nut in the body panel. Continue to tight-en the M8 Hex Bolt until the Rivet Nut is fully compressed and close to flush with the surface. Remove bolt and tool from the Rivet Nut, (Fig 21). WARNING: Do not over tight-en the hex bolt or the Rivet Nut may become damaged.
- g. Repeat Step 3 to drill the 5/16” hole through the pinch weld as needed.
- h. Select the passenger side 3rd Mounting Bracket. Attach the Bracket to the M8 Rivet Nut and M8 Clip Nut with (2) M8X1.25-25mm Hex Bolts, (2) M8 Lock Washers and (2) M8 Large Flat Washers, (Fig 22). Do not fully tighten hardware at this time.
- i. Repeat Steps a—h to install the identical 4th Bracket, (Figs 23-24).
-
STEP 10
Select the Passenger Side Running Board. Slip (4) M6X1-20mm Square Head Bolts into each bottom channel (Fig 8). Carefully position the Running Board onto the (4) Mounting Brackets.
Repeat Step 6 to attach the Running Board to the Mounting Brackets. -
STEP 11
Level and adjust the Running Board and fully tighten all hard-ware.
Attention
Do periodic inspections to the installation to make sure that all hardware is
secure and tight.
In order to protect your bars/boards, please use mild soap/non-abrasive
products for cleaning only.
Customer Support: info@iboardauto.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>