BANNER Q90R R-GAGE Radar Sensor User Guide
- June 1, 2024
- BANNER
Table of Contents
BANNER Q90R R-GAGE Radar Sensor
Specifications
- Range: 0.15 m to 20 m (0.5 ft to 65.6 ft)
- Supply Voltage (Vcc):
- Analog Voltage models: 12 V DC to 30 V DC
- Analog Current and Dual Discrete models: 10 V DC to 30 V DC
- Use only with a suitable Class 2 power supply (UL) or Limited Power Supply (CE)
Product Usage Instructions
Installation and Setup
- Ensure the device and its antenna are at least 20 cm away from all persons to meet RF exposure requirements.
- Refer to the Instruction Manual at www.bannerengineering.com using part number 236054 for comprehensive programming, performance, and troubleshooting information.
Features and Indicators
LED | 1 | 2 | 3 | 4 |
---|---|---|---|---|
Description | Power ON | Signal Strength | Output 1 | Output 2 |
Color | Green | Green | Amber | Amber |
Description | Power ON | Signal strength indication | Target is within the taught |
analog span or discrete output
status| Discrete output status
Wiring Options
For detailed wiring options, refer to the provided diagrams in the manual based on your specific setup requirements.
Radar Configuration Software
To configure the sensor using software, visit the Banner Engineering website at the provided link for more information.
Quick Start Guide
Radar-Based Sensors for Detection and Measurement of Moving and Stationary
Targets. Patent pending.
This guide is designed to help you set up and install the Q90R R-GAGE sensor.
For complete information on programming, performance, troubleshooting,
dimensions, and accessories, please refer to the Instruction Manual at
www.bannerengineering.com. Search for part number 236054 to view the
Instruction Manual. Use of this document assumes familiarity with pertinent
industry standards and practices.
WARNING:
- Do not use this device for personnel protection
- Using this device for personnel protection could result in serious injury or death.
- This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A device failure or malfunction can cause either an energized (on) or de-energized (off) output condition.
IMPORTANT : To satisfy RF exposure requirements, this device and its antenna must operate with a separation distance of at least 20 cm from all persons.
Features and Indicators
Wiring
- Quick disconnect wiring diagrams are functionally identical.
- NOTE : Banner recommends that the shield wire (quick-disconnect cord sets only) be connected to earth ground or dc common. Shielded cord sets are recommended for all quick-disconnect models.
Radar Configuration Software
For more information, visit www.bannerengineering.com/us/en/products/sensors/software/radar- configuration.html.
Specifications
Range
The sensor can detect an object at the following range, depending on the
material of the target: 0.15 m to 20 m (0.5 ft to 65.6 ft)
- Supply Voltage (Vcc)
- Analog Voltage models: 12 V DC to 30 V DC
- Analog Current and Dual Discrete models : 10 V DC to 30 V DC
- Use only with a suitable Class 2 power supply (UL) or
- Limited Power Supply (CE)
- Power and Current Consumption, exclusive of load
- Power consumption: < 2.4 W
- Current consumption: <100 mA at 24 V DC
- Operating Temperature
- Standard model: –40 °C to +65 °C (–40 °F to +149 °F)
- Output Ratings
- Analog Outputs:
- Current Output (Q90R….-.I.. models): 1 kΩ maximum load resistance at 24 V; maximum load resistance = [(Vcc – 4.5)/ 0.02 Ω]
- Voltage Output (Q90R….-.U.. models): 2.5 kΩ minimum load resistance
- Current rating = 50 mA maximum each
Certifications
Banner Engineering BV
Park Lane, Culliganlaan 2F bus 3 1831 Diegem, BELGIUM
Turck Banner LTD Blenheim House Blenheim Court
Wickford, Essex SS11 8YT
GREAT BRITAIN
- ETSI EN 305 550 V2.1.0
- ETSI EN 305 550-1 V.1.2.1
- ETSI EN 305 550-2 V.1.2.1
- FCC ID: UE3Q90R
- IC: 7044A-Q90R6
- Install where not accessible by unauthorized personnel.
- The device shall only be accessible for adjustment, programming, or maintenance.
- The device was evaluated for IK08 impact energy in accordance with IEC 62262.
Representative Beam Pattern
Dimensions
All measurements are listed in millimeters [inches], unless noted otherwise.
Banner Engineering Corp Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER THE COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE. This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. Specifications and product information in English supersede that which is provided in any other language. For the most recent version of any documentation, refer to: www.bannerengineering.com.
For patent information, see www.bannerengineering.com/patents.
- Document title : Q90R R-GAGE Radar Sensor Quick Start Guide
- Part number: 236054
- Revision: B
- Original Instructions
© Banner Engineering Corp. All rights reserved.
FAQS
Q: What should I do if the sensor is not detecting targets within the specified range?
A: Check the power supply voltage to ensure it falls within the specified range for the model you are using. Additionally, verify that no obstructions are blocking the sensor's view.
Q: How can I switch between PNP and NPN settings for the outputs?
A: Refer to the user manual for instructions on configuring the push-pull outputs to switch between PNP and NPN settings based on your requirements.
Q: Can I use shielded cordsets with all quick-disconnect models?
A: Yes, it is recommended to use shielded cordsets with all quick-disconnect models, and Banner recommends connecting the shield wire to earth ground or dc common.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>