HD Ridez WB-CS222SD OE Style Matte Black Nerf Bars Running Boards Installation Guide

HD Ridez WB-CS222SD OE Style Matte Black Nerf Bars Running Boards

Product Information

Specifications:

• Product: S6 Running Boards
• Vehicle Compatibility: 2021-2024 Chevy Suburban
• Part Numbers: WB-CS222SD (Driver/Left), WB-CS222BD (Passenger/Right)
• Material: Steel
• Includes: Running boards, mounting brackets, bolts, washers, and lock nuts

Product Usage Instructions

Installation Steps:

1. Identify the parts from the parts list provided.
2. Clean the running boards using mild soap.
3. Begin with the passenger/right side installation by removing any existing hardware.
4. Attach the mounting brackets to the designated locations on the vehicle as shown in the manual.
5. Insert double bolt plates into the tracks on the bottom of the running board.
6. Securely attach the running board to the mounting brackets using the provided hardware.

Maintenance:

To maintain the running boards, avoid using abrasive polishes or waxes that could damage the finish. Clean with mild soap when necessary.

Additional Tips:

• Ensure all bolts are tightened securely to prevent any movement or rattling.
• Regularly inspect the running boards for any signs of wear or loose components.

FAQ (Frequently Asked Questions):

• Q: Can these running boards be painted to match my vehicle’s color?
  A: Yes, these running boards can be painted; however, it is recommended to consult a professional for best results and to ensure proper adhesion.

• Q: Are these running boards compatible with other vehicle models?
  A: These specific running boards are designed for use with 2021-2024 Chevy Suburban models. Compatibility with other vehicles may vary, so it is recommended to check with the manufacturer for fitment information.

S6 RUNNING BOARDS 21-24 CHEVY SUBURBAN PART#WB-CS222SD/WB-CS222BD

PARTS LIST

OVERVIEW

PROCEDURE

1. REMOVE CONTENTS FROM THE BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY. USE ILLUSTRATION TO IDENTIFY BRACKETS AND SIDEBARS.
2. Starting on the Passenger/Right front of the vehicle, remove the plastic plugs covering the threaded holes in the body panel, if equipped, (Figure 1). Select (1) Mounting Bracket. Attach the Bracket to the vehicle with (2) 8mm Hex Bolts, (2) 8mm Lock Washers, and (2) 8mm Flat Washers, (Figure 2). Do not tighten the hardware. NOTE: The Mounting Brackets look similar but are unique. The Front/Rear Mounting Brackets have a shorter rear-facing mounting tab and the Center Mounting Brackets have a notch and longer forward-facing mounting tabs, (Figure 3).
3. Repeat Step 2 to install (3) Mounting Brackets to the 2nd, 3rd, and rear mounting locations, (Figures 4—6). Do not tighten the hardware.
4. Unwrap the Passenger/Right S6 Running Board. Select (3) 8mm Double Bolt Plates, (Figure 7). Insert the Bolt Plates into the channel at the bottom of the Running Board.
5. Place the Running Board on top of the (3) Mounting Brackets. Lift the Running Board up and guide the studs down through the Brackets. IMPORTANT: Do not slide the Running Board on the Brackets, (front to back or rotate), or the finish on the Running Board may be damaged.
6. Attach the Running Board to the Brackets with (6) 8mm Flat Washers and (6) 8mm Nylon Lock Nuts, (Figure 8). Do not tighten the hardware.
7. Level and adjust the S6 Running Board and tighten all hardware.
8. Repeat Steps 2—7 to attach the Driver/Left S6 Running Board.
9. Do periodic inspections of the installation to make sure that all hardware is secure and tight.

To protect your investment , Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Running Boards.

Passenger/Right Side Installation Pictured

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>