Acmeda CR2450 Bottom Up Remote Control User Guide

Acmeda CR2450 Bottom Up Remote Control

Specifications:

• Voltage: 3V (CR2450)
• Frequency: 433.92 MHz
• Transmitting Power: 10 milliwatt
• Ambient Operating Temperature: Not specified
• Transmission Distance: Up to 200 meters (open space)

Product Usage Instructions

1. Wall Mount Holder Installation:
   Remove the cover from the base using a flat head screwdriver. Attach the base to the wall using the supplied fasteners and anchors.

2. Remote Battery Replacement:
   Remove the cover from the remote by pressing gently to disengage it. Install the battery with the positive side facing up. Replace the cover by snapping it into place.

3. Levelling Control:
   Use the levelling control bar to set your preferred shade position. It ensures that all shades aligned to the same position when controlling a group of shades.

4. Selecting a Channel:
   For multi-channel remotes, hold the CH button and within 4 seconds press UP or DOWN to select the desired channel. Press CH or STOP to confirm.

5. Protocol Selection:
   This device can operate Acmeda line EL motors. To toggle between ARC & EL modes, hold P2 while inserting the battery. Screen flashes X 5, 1 = ARC Mode, 2 = EL Mode.

6. Hide Unused Channels:
   You can configure your multi-channel remote to display only selected channels. Hold STOP and CH, then select the required channel quantity by pressing UP or DOWN. Press STOP to confirm.

7. Disable Limit Setting Function:
   To prevent accidental changes in limit settings, switch to User Mode by holding the right button for 5 seconds. A short press displays the current mode on the LCD (L for locked, U for unlocked).

FAQ:

Q: How do I dispose of batteries and damaged electrical products?
A: Do not dispose of them in general waste. Please recycle batteries and damaged electrical products appropriately.

REMOTE CONTROL USERS GUIDE
15 CHANNEL

TECHNICAL DATA / PACKAGE CONTENTS

TECHNICAL SPECIFICATIONS

Voltage:| 3V (CR2450)
Frequency:| 433.92 MHz
Transmitting Power:| 10 milliwatt
Ambient Operating Temperature:| -10°C -50°C
Transmission Distance:| up to 200 meters (open space)

PACK CONTENTS

• 1 x remote (Single or Fifteen Channel)
• 1 x magnetic holder Inc. wall fixing screws
• 1 x Instruction manual
• 1 x 3V – CR2450 battery

SAFETY

WARNING: Important safety instructions to be read before installation and use.
Incorrect installation or use can lead to serious injury and will void manufacturer’s liability and warranty.
It is important for the safety of persons to follow the enclosed instructions. Save these instructions for future reference.

• Do not expose to water, moisture, humid and damp environments or extreme temperatures.
• Persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge
• should not be allowed to use this product.
• Use or modification outside the scope of this instruction manual will void warranty.
• Installation and programming to be performed by a suitably qualified installer.
• Follow installation instructions.
• For use with motorized shading devices.
• Keep away from children.
• Frequently inspect for improper operation. Do not use if repair or adjustment is necessary.
• Keep clear when in operation.
• Replace battery with correctly specified type.

The manufacturer declares this equipment is in compliance with the essential requirements and other relevant provisions of R&TT EC Directive 1999/5/EC

Statement Regarding FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Note:

• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
• However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which Can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.
• Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Do not dispose of in general waste.
Please recycle batteries and damaged electrical products appropriately.

FUNCTIONAL OVERVIEW

Wall mount holder

• Remove cover from base by prying with flat head screwdriver.
• Use supplied fasteners and anchors to attach the base to wall.
  Replace cover by pressing snap latches into place.

Remote battery

• Remove cover from remote press gently in and down to disengage cover.
• Install battery with positive (+) side facing up.

Buttons

Levelling control
The levelling control bar can be used to visualize and accurately set your preferred shade position. When used to control a group of shades, they will all perfectly align to the same position.

Selecting a channel – (multi channel remote)

• Hold CH button.
• Within 4 seconds press UP or DOWN to select desired channel .
• Press CH or STOP to confirm

IMPORTANT
If no button is pressed within 4 seconds, the channel selection will automatically be confirmed

Group control using CH “0”
Channel “0” is pre-set to control ALL shades paired within your multi-channel remote. To create a customized group channel ref to section 6

PROGRAMMING

IMPORTANT
Please refer to the the relevant documentation of your motor model for instructions on adjusting motor settings.

Protocol selection
This device can be configured to operate Acmeda line “EL” motors. (The default mode is ARC protocol). To toggle between ARC & EL modes follow the following steps.

• Screen flashes “1” = ARC Mode
• Screen flashes “2” = EL Mode

Hide unused channels
Your multi channel remote can be configured to have anywhere between 1 or 15 visible channels. Inactive channels will not be visible when scrolling through the CH selection.

• Hold STOP  and CH
• Continue holding CH and select required channel qty by pressing UP or DOWN
• Press STOP to confirm

Disable limit setting function of remote

IMPORTANT

• This mode is intended to be used after all shade programming is completed.
• User Mode will prevent accidental or unintended changing of limits. 

It is still possible to add or delete channels and perform P2 functions, while the lock function is enabled.

Using Motor P1 Button

Using a pre-existing Controller

• A= Existing controller or channel (to keep)
• B= Controller or channel to add or remove

IMPORTANT
Consult user manual for your controller or sensor.

TROUBLESHOOTING

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>