Rollease Acmeda MT02-0101 Basic Remote 5ch User Guide
- June 1, 2024
- ROLLEASE ACMEDA
Table of Contents
Rollease Acmeda MT02-0101 Basic Remote 5ch
Product Information
Specifications:
- Model: Basic Remote 5ch
- Programming Guide: MT02-0101-069011_v1.3_16022024
- Channels: 5
- Battery: Coin/button cell battery
- Compliance: FCC Part 15, ISED RSS(s)
Product Usage Instructions
Pairing with Remote:
- Select the desired channel by scrolling using the arrows on the remote control.
- Press the P1 button on the motor for 2 seconds until the motor responds with JOG and BEEP.
- Within 4 seconds, hold the stop button on the remote for 3 seconds to pair.
Safety Instructions:
Incorrect installation or use can lead to serious injury. Follow enclosed instructions for safety. Do not ingest the battery to avoid chemical burn hazard. Keep batteries away from children.
Battery Management:
For battery motors, prevent discharging completely for extended periods. Recharge as soon as the battery is discharged. Charge your motor for 6-8 hours as per motor instructions. Low battery warning is indicated by LED flickering.
P1 Location and Motor Head Functions:
- a. Control UP/STOP/DOWN of the Shade: Short press motor head button after setting limits and motor is not in sleep mode.
- b. Adding/Removing Controller: Press motor head button for 2 seconds then JOG*1 within 10 seconds.
- c. Sleep mode, RF control inactive: Hold motor head button for 6 seconds then JOGx2 to activate or deactivate RF control.
- d. Direction Reverse: Hold motor head button for 10 seconds then JOGx3.
- e. Reset: Hold motor head button for 14 seconds then JOGx4.
Frequently Asked Questions
Q: What should I do if the motor does not respond to the remote?
A: Ensure proper pairing by following the pairing instructions. If issues persist, contact a technician for help.
Q: How long should I charge the motor?
A: Charge your motor for 6-8 hours depending on the model, as per the motor instructions provided.
SAFETY
Incorrect installation or use can lead to serious injury and will void
manufacturer’s liability and warranty. It is important for the safety of
persons to follow the enclosed instructions.
Save these instructions for future reference.
WARNING: Do not ingest battery, Chemical Burn Hazard.
- Do not expose to water, moisture, humid and damp environments or extreme temperatures.
- Persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, should not be allowed to use this product.
- Use or modification outside the scope of this instruction manual will void warranty.
- Installation and programming to be performed by a suitably qualified installer.
- Follow installation instructions.
- For use with motorized shading devices.
- Frequently inspect for improper operation.
- Do not use if repair or adjustment is necessary.
- Keep clear when in operation.
- Replace battery with correctly specified type.
- This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
- Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children.
- If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
FCC & ISED STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Caution: Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to operate
the equipment.
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequencyenergy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
ASSEMBLY
Please refer to separate Rollease Acmeda System Assembly Manual for full assembly instructions relevant to the hardware system being used.
BATTERY MANAGEMENT
For battery motors;
Prevent discharging the battery completely for extended periods, recharge as
soon as the battery is discharged.
CHARGING NOTES
Charge your motor for 6-8hours, depending on the motor model, as per motor
instructions.
During operation, if battery is low,the LED in motor will flicker 8 times to gave a low-voltage alarm when motor starts.
P1 LOCATION AND MOTORHEAD FUNCTIONS
- a. Control the UP/STOP/DOWN of the Shade: Short press motor head button (can only operate after the limits are set and motor is not in sleep mode)
- b. Adding/Removing Controller: Press motor head button for 2S–>JOG*1 (Operation needs be done within 10S )
- c. Sleep mode, RF control inactive: Hold motor head button for 6S –>JOGx2 ( Same operation to active off RF control)
- d. Direction Reverse :hold motor head button for 10S–JOGx3
- e. Reset: hold motor head button for 14S–>JOGx4
HOW TO CHARGE LI_ION ZERO WIRE-FREE MOTOR
BUTTON OVERVIEW
REPLACE BATTERY
WALL MOUNTING
REMOTE CONTROL PARAMETERS
Electrical
Specification
| Standard
---|---
Battery Type| AAA battery*2
Working Temperature| -10°C-50°C
Radio Frequency| 433.92M±100KHz
Transmit Distance| >=30m indoor
INSTALLER
This setup wizard should be used for new installation or factory reset motors
only.
Individual steps may not work if you haven’t followed the setup from the
beginning.
Pairing with Remote
STEP 1.
Select the desired channel you wish to program by scrolling using the arrows
on the remote control
Within 4 seconds hold the stop button on the remote for 3 seconds.
Check direction
STEP 2.
Press up or down to check the motor direction. If correct skip to step 4.
Change direction
STEP 3.
If the shade direction needs to be reversed: press and hold the up & down
arrow together for 2 sec until the motor Jogs
Set top limit
STEP 4.
Move shade to desired top limit by pressing the up arrow repeatedly. Then
press and hold up & stop together for 2 sec to save limit.
Tap the arrow several times or hold down if needed: press arrow to stop.
Set Bottom limit
STEP 5.
Move shade to desired bottom limit by pressing the down arrow repeatedly. Then
press and hold down & stop together for 2 sec to save limit.
Tap the arrow several times or hold down if needed: press arrow to stop.
Factory reset
To reset all settings in the motor press and hold the P1 Button for 14 seconds, you should see 4 independent jogs followed.
Remove or add remote
Using the P1 button, press and hold the button for 2S. The motors will JOG x1. Then , hold the STOP about 2S on remote to add or remove. The motor will respond with JOG x2 to add remote, the motor will resond with JOG x1 to remove remote.
Remove or add remote
Using a pre-existing Remote: press the Prg button on existing remote, shade will respond with JOGx1. Then, press Prg button on existing remote, and the shade will respond with JOGx1. Finally, press STOP on new controller to add the remote and the shade will JOGx2, press STOP on new controller to remove the remote and the shade will JOGx1.
Set favorite position
Move shade to the desired position by pressing the UP or Down button on the Remote. After that , press and Hold CH> and STOP buttons together on the remote for about 2S. Shade will JOGx2
Delete favorite position
To Delete the favorite position, Press and Hold CH> and STOP together on the remote for about 2S. Shade will JOGx1
Change Motor speed
To Increase motor speed: Press the Prg button on Remote. Shade will JOGx1, Then, press the STOP button, shade will JOGx1, press UP button once and shade will JOGx1 again.
Change Motor speed
To decrease motor speed: Press the Prg button on Remote. Shade will JOGx1, Then, press the STOP button, shade will JOGx1, press Down button once and shade will JOGx1 again.
Adjust the limits
To Adjust upper limit, press and hold both UP and STOP for about 5S. Shade will JOGx1. Then, press UP button to save upper limit, hold UP and STOP 2S and the shade will JOGx2
To Adjust lower limit, press and hold both DOWN and STOP for about 5S. Shade will JOGx1. Then, press DOWN button to save lower limit, hold DOWN and STOP 2S and the shade will JOGx2
Canceling the limits
Press the Prg button on Remote, shade will JOGx1 Then, press STOP on remote and the shade will JOGx1 again. Finally, press Prg on remote and shade will JOGx1 once again to canceling the limits
Entering in tilt mode
Press Prg button on Remote and shade will JOGx1. Then, press STOP, shade will JOGx1, and press STOP and the shade will JOGx1 once again.
Battery Check
Documents / Resources
|
Rollease Acmeda MT02-0101 Basic Remote
5ch
[pdf] User Guide
MT02-0101 Basic Remote 5ch, MT02-0101, Basic Remote 5ch, Remote 5ch, 5ch
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>