ROLLEASE ACMEDA MT01-1325-069002 Automate Li-Ion and DC Motor Instruction Manual

June 12, 2024
ROLLEASE ACMEDA

ROLLEASE ACMEDA MT01-1325-069002 Automate Li-Ion and DC Motor

ROLLEASE-ACMEDA-MT01-1325-069002-Automate-Li-Ion-and-DC-Motor-
PRODUCT

Product Information

  • MOTOR PROGRAMMING INSTRUCTIONS
  • Compatible with Li-ion & DC Motors
  • Features SOFT STOP for smooth motor operation
  • Includes ELECTRONIC LIMIT for precise positioning
  • SELECTABLE SPEED allows customization of motor speed
  • Operates on a 433 MHZ BI-DIRECTIONAL frequency
  • FAVORITE POSITION function for easy access to preferred settings
  • BATTERY CHECK feature to monitor battery level
  • USB CHARGE option available for Li-ion Motors
  • SOLAR OPTION for alternative power source
  • LEVEL CONTROL for adjusting motor position
  • BATTERY POWERED operation
  • AUTOMATE V3.2_PRGM_APRIL_2022 version

Product Usage Instructions

  1. ASSEMBLY: Follow the assembly instructions provided in the manual.
  2. RETROFIT INSTALLATION: Install the motor according to the retrofit installation instructions.
  3. CHARGING: If using a Li-ion Motor, connect it to a USB charger to charge the battery. Refer to the charging instructions for more details.
  4. P1 BUTTON FUNCTIONS: Familiarize yourself with the various functions of the P1 button, including Motor state test and Motor configuration options. Refer to section 4.1 and 4.2 of the manual for detailed instructions.
  5. BATTERY CHECK FUNCTION: Use the Battery Check function to monitor the battery level. Follow the instructions in section 12 of the manual to perform this function.
  6. SEND SHADE TO BATTERY CHARGE LEVEL: Utilize this function to send the shade to the battery charge level. Refer to section 12.1 for step-by-step instructions.
  7. CHARGING LED: Learn how to turn the Charging LED on or off by following the instructions in section 13.1 of the manual.
  8. SLEEP MODE: Understand how to activate and deactivate the Sleep Mode feature. Refer to section 14 for instructions.
  9. TROUBLE SHOOTING: If you encounter any issues, consult the troubleshooting section (15) of the manual for possible solutions.
  10. INITIAL SET UP: Complete the initial set up process as outlined in the manual.

Features

ROLLEASE-ACMEDA-MT01-1325-069002-Automate-Li-Ion-and-DC-Motor-
FIG 1

SAFETY INSTRUCTIONS

WARNING: Important safety instructions to be read before installation.
Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.ROLLEASE-ACMEDA-MT01-1325-069002-Automate-Li-Ion-and-
DC-Motor-FIG 2

WARNING: Important safety instructions to be read before installation and use.
Incorrect installation or use can lead to serious injury and will void manufacturer’s liability and warranty.
It is important for the safety of persons to follow the enclosed instructions. Save these instructions for future reference.

  • Do not expose to water, moisture, humid and damp environments or extreme temperatures.
  • Persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge should not be allowed to use this product.
  • Use or modification outside the scope of this instruction manual will void warranty.
  • Installation and programming to be performed by a suitably qualified installer.
  • Follow installation instructions.
  • For use with motorized shading devices.
  • Keep away from children.
  • Frequently inspect for improper operation. Do not use if repair or adjustment is necessary.
  • Keep clear when in operation.
  • Replace battery with correctly specified type.

COMPLIANCE STATEMENT

FCC  STATEMENT

This device complies with Part 15 of the FCC Rules / Industry Canada licence- exempt RSS standard(s). Operation is subject to the following two conditions:

  1. this device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation.
To ensure compliance, operations at closer than this distance is not recommended.

ASSEMBLY

ZERO HEAD ADAPTERROLLEASE-ACMEDA-MT01-1325-069002-Automate-Li-Ion-and-DC-
Motor-FIG 3

GENERIC CROWN, DRIVE & TUBE ASSEMBLY

ZERO HEAD ANTENNA WRAP

RETROFIT INSTALLATION

(1.1Nm & 2.0Nm MOTOR ONLY)ROLLEASE-ACMEDA-MT01-1325-069002-Automate-Li-
Ion-and-DC-Motor-FIG 6

CHARGING/POWER SUPPLY

ROLLEASE-ACMEDA-MT01-1325-069002-Automate-Li-Ion-
and-DC-Motor-FIG 7

  1. (LI-ION 1.1Nm & 2.0Nm ONLY)
  2. (LI-ION 3.0Nm & 10.0Nm ONLY)
  3. (DC 1.1Nm & 2.0Nm ONLY)

P1 BUTTON FUNCTIONS

Motor state test

This table describes the function of a short P1 Button press/release (<2 seconds) depending on curr ent motor configuration.

P1

Press

| Condition| Function Achieved| Visual Feedback| Audible Feedback| Function Described
---|---|---|---|---|---

Short Press

| If limit is NOT set| None| No Action| None| No Action

If limits are set

| Operational control of motor, run to limit. Stop if running|

Motor Runs

|

None

| Operational control of motor after pairing and limit setting is completed first time
If motor is in “Sleep Mode” & limits are set|

Wake and control

| Motor wakes and runs in a direction|

None

| Motor is restored from Sleep Mode and RF control is active

Motor configuration options

The P1 Button is utilized to administer motor configurations as described below.
Hold P1 button on motor head.

Activate Pairing Mode

Sleep Mode

Reverse Direction

Reset To Factory SettingsROLLEASE-ACMEDA-MT01-1325-069002-Automate-Li-
Ion-and-DC-Motor-FIG 12

INITIAL SET UP

Pair motor with controllerROLLEASE-ACMEDA-MT01-1325-069002-Automate-Li-
Ion-and-DC-Motor-FIG 13

Motor is now in step mode and ready for setting limits

Check motor directionROLLEASE-ACMEDA-MT01-1325-069002-Automate-Li-Ion-
and-DC-Motor-FIG 14

IMPORTANT

  • Damage to shade may occur when operating motor prior to setting limits. Attention should be given.
  • Reversing motor direction using this method is only possible during initial set-up

Set LimitsROLLEASE-ACMEDA-MT01-1325-069002-Automate-Li-Ion-and-DC-Motor-
FIG 15ROLLEASE-ACMEDA-
MT01-1325-069002-Automate-Li-Ion-and-DC-Motor-FIG 16

IMPORTANT

After setting limits, motor will automatically exit from initial set-up mode.

ADJUSTING LIMITS

Adjust upper limitROLLEASE-ACMEDA-MT01-1325-069002-Automate-Li-Ion-and-
DC-Motor-FIG 17

Adjust lower limitROLLEASE-ACMEDA-MT01-1325-069002-Automate-Li-Ion-and-
DC-Motor-FIG 18

IMPORTANT

The bottom limit should be set ~ 1.38 in. (35mm) below the Ultra-Lock to disengage the auto lock mechanism when the shade is raised.

CONTROLLERS AND CHANNELS

Using P2 Button on existing controller to add a new controller or channel

  • A = Existing controller or channel (to keep)
  • B = Controller or channel to add or removeROLLEASE-ACMEDA-MT01-1325-069002-Automate-Li-Ion-and-DC-Motor-FIG 18
  • A = Existing controller or channel (to keep)
  • B = Controller or channel to add or removeROLLEASE-ACMEDA-MT01-1325-069002-Automate-Li-Ion-and-DC-Motor-FIG 19

FAVORITE POSITIONING

Set a favorite positionROLLEASE-ACMEDA-MT01-1325-069002-Automate-Li-Ion-
and-DC-Motor-FIG 35

Send shade to favorite position Delete favorite positionROLLEASE-
ACMEDA-MT01-1325-069002-Automate-Li-Ion-and-DC-Motor-FIG
21

TILT & ROLLER MODE

Toggle motor to Tilt Mode

Default motor mode is Roller after initial Limits have been set, use following steps to change to Roller Mode.

Toggle Motor to Roller Mode

ADJUSTING SPEED

Increase Motor Speed

Default motor mode is the slowest speed.ROLLEASE-ACMEDA-MT01-1325-069002
-Automate-Li-Ion-and-DC-Motor-FIG 27

Decrease Motor SpeedROLLEASE-ACMEDA-MT01-1325-069002-Automate-Li-Ion-and-DC-
Motor-FIG 28

SOFT STOP CONFIGURATION

Turn Soft Stop OFF

Motor must be in slowest speed to turn Soft Stop OFF.ROLLEASE-ACMEDA-
MT01-1325-069002-Automate-Li-Ion-and-DC-Motor-FIG 29

Turn Soft Stop ON

Motor must be in fastest speed to turn Soft Stop ON.ROLLEASE-ACMEDA-
MT01-1325-069002-Automate-Li-Ion-and-DC-Motor-FIG 30

BATTERY CHECK FUNCTION

Send Shade to battery charge levelROLLEASE-ACMEDA-MT01-1325-069002
-Automate-Li-Ion-and-DC-Motor-FIG 31

CHARGING LED

(ONLY FOR LI-ION MOTORS)

Turn Charging LED ON/OFF

Motor must be at Lower Limit.ROLLEASE-ACMEDA-MT01-1325-069002-Automate-Li-
Ion-and-DC-Motor-FIG 32

SLEEP MODE

If multiple motors are grouped on a single channel, Sleep Mode may be used to put all but 1 motor to sleep, allowing programming of just the one motor that remains “Awake”. See page 6 for detailed P1 functions.

Enter Sleep Mode
Sleep mode is utilized to prevent a motor from incorrect configuration during other motor setup.
Hold P1 button on the motor head

Exit Sleep Mode: Method 1
Exit sleep mode once the shade is ready.
Press and release P1 button on the motor head

Exit Sleep Mode: Method 2
Remove power and then re-power the motor.

TROUBLE SHOOTING

Problem Cause Remedy
Motor is not responding Battery in motor is depleted or Power Supply is not
working Recharge with a compatible charger
Insufficient charging from solar PV panel Check connection and orientation of

PV panel
Transmitter battery is discharged| Replace battery
Battery is inserted incorrectly into transmitter| Check battery polarity
Radio interference/shielding| Ensure transmitter is positioned away from metal objects and the aerial on motor or receiver is kept straight and away from metal
Receiver distance is too far from transmitter| Move transmitter to a closer position
Charging failure| Check power supply to motor is connected and active
Motor beeps x10 when in use| Battery voltage is low| Recharge with a compatible charger
Cannot program a single motor (multiple motors respond)| Multiple motors are paired to the same channel| Always reserve an individual channel for programming functions. Use Sleep Mode to program individual motors.

ROLLEASE ACMEDA | USA
Level 7 / 750 East Main Street
Stamford, CT 06902, USA
T +1 800 552 5100 | F +1 203 964 0513

ROLLEASE ACMEDA | AUSTRALIA
110 Northcorp Boulevard,
Broadmeadows VIC 3047, AUS
T +61 3 9355 0100 | F +61 3 9355 0110

ROLLEASE ACMEDA | EUROPE
Via Conca Del Naviglio 18,
Milan (Lombardia) Italy
T +39 02 8982 7317 | F +39 02 8982 7317

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals