ROLLEASE ACMEDA MT02-0401-069007 ARC Repeater User Guide

: June 6, 2024
: ROLLEASE ACMEDA

Table of Contents

INSTALLATION RANGE
ROLLEASE ACMEDA USB POWER ADAPTERS
LED LIGHT INDICATION
SPECIFICATIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MT02-0401-069007 ARC Repeater
User Guide

Plug a USB power adapter into a power outlet.

WARNING
Only use Rollease Acmeda USB power adapters with ARC Repeater.
Using other power adapters/power sources may adversely affect ARC Repeater performance and should be avoided.

Plug the ARC Repeater into the USB power adapter.
A blue LED on the ARC Repeater will be visible when the power is switched on.

NOTE
ARC Repeater is plug-and-play. No setup is required.

Press any button on a Rollease Acmeda remote control. The blue light on the ARC Repeater will flash 3 times. This means the ARC Repeater is transmitting the signal.

IMPORTANT
A maximum of 2 ARC Repeaters can be used in one project Don’t cover the ARC Repeater with a metal shield

INSTALLATION RANGE

The Rollease Acmeda ARC Repeater can extend the RF range of operation for ARC- enabled products by up to 40m (131ft).

ROLLEASE ACMEDA MT02 0401 069007 ARC Repeater - INSTALLATION
RANGE

NOTE: RF source can be PULSE or an ARC Remote Control or Sensor.

ROLLEASE ACMEDA USB POWER ADAPTERS

REGION	AU	EU	UK	US
PART	MTPS-U585-1000AU	MT03-0301-069009	MTPS-U585-100EU	MT03-0301-050002

MT03-0301-069008
| | | | |
IN 90° ORIENTATION
FOR A BETTER SIGNAL RANGE| | | | |

LED LIGHT INDICATION

LED	STATUS
On	Power On
Flashes x 3	Transmitting a remote control, motor, or sensor RF433 MHz signal
Flashes x 1	Transmitting a Pulse hub RF433 MHz signal

SPECIFICATIONS

INTERFACE	USB
WORKING VOLTAGE	5±0.2 V DC
POWER SUPPLY	USB POWER ADAPTER
RADIOFREQUENCY	433.92MHZ

REGULATORY COMPLIANCE
Rollease Acmeda declares this equipment is in compliance with the essential requirements and other relevant provisions of the following directives:
2014/35/EU – The Low Voltage Directive
2014/30/EU – The Electromagnetic Compatibility Directive
2014/53/EU – The Radio Equipment Directive

This device complies with Part 15 of the FCC Rules / Industry Canada licence- exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC ID: 2AGGZMT020401007
IC: 21769-MT020401007

Do not dispose of the general waste.
Please recycle batteries and damaged electrical products appropriately.