ROLLEASE ACMEDA MT02-0101-069011 5CH Remote Control User Manual

ROLLEASE ACMEDA MT02-0101-069011 5CH Remote Control

Product Information

Product Name: MT02-0101-069011 5CH Remote Control

Specifications:

• Model: MT02-0101-069011
• Number of Channels: 5
• Compatibility: Motor operation instruction manual
• FCC Compliance: Class B digital device

Product Usage Instructions

Remote Controller Buttons

• The remote controller should not be exposed to moisture or impact to ensure its longevity.
• If the remote control distance is significantly shorter or less sensitive during use, please check the battery. Replace the battery if necessary.
• If the voltage is too low, the orange LED will flicker during operation, indicating that the battery needs to be replaced. Properly dispose of used batteries according to local garbage classification and recycling policy.

Instruction

Prohibit Dual-key Operation:

1. Press Prg x10s, LED flickers trice.
2. Repeat step 1 to activate dual-key operation.
   Note: When dual-key operation is prohibited, certain programming setting functions are not allowed.

Number of Channels Setting:

1. Press CH- and CH+ together for 3 seconds, LED flickers trice.
2. Short press CH- or CH+.
3. Short press Stop, LED flickers twice.
   Note: When all LEDs are lit, it represents channel 0 where all channels move together.

For other operations, please refer to the motor operation instruction manual.

FCC Compliance

• Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
• These limits are designed to provide reasonable protection against harmful interference in a residential installation.
• This equipment generates and uses radio frequency energy and may cause harmful interference to radio communications if not installed and used in accordance with the instructions.
• If this equipment causes harmful interference to radio or television reception, try the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a different circuit from the receiver.
  • Consult the dealer or an experienced radio/TV technician for help.

FAQ

1. How should I dispose of used batteries?
   Please follow the local garbage classification and recycling policy to properly dispose of used batteries.

2. What should I do if the remote control distance is shorter or less sensitive?
   Check the battery and replace it if necessary. Low voltage can cause reduced range and sensitivity.

3. How do I activate dual-key operation?
   To activate dual-key operation, press Prg x10s and repeat the step. The LED will flicker trice to indicate activation.

4. What does it mean when all LEDs are lit?
   When all LEDs are lit, it represents channel 0 where all channels move together.

MT02-0101-069011
5CH Remote Control

Remote Controller Buttons

Caution!

1. The transmitter should not be exposed to moisture or impact, so as not to affect its life.
2. During use, when the remote control distance is significantly shorter or less sensitive, please check whether the battery needs to be replaced.
3. When the voltage is too low, orange LED will flicker during operation, indicating to replace the battery.
4. Please properly dispose of used batteries according to the local garbage classification and recycling policy.

 Instruction

1. Prohibit Dual-key Operation

2. Press “Prg” x10s, LED flickers trice

3. Repeat the above, dual-key operation activated
   Note: When dual-key operation prohibited, these programming setting function are not allowed

4.  Number of Channels Setting
   Press” CH-” & “CH+” together for 3s, LED flickers trice, short press”CH-” or “CH+”, then short press “Stop”,LED flickers twice.
   Note: When all LEDs are lit, that is channel 0 (All channels move together).

5.  For other operations, please refer to the motor operation instruction

FCC Compliance

This device complies with Part 15 of the FCC Rules / Innovation, Science and Economic Development Canada’s licence-exempt RSS standard(s).
Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

• If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>