HAYLOU X1 Pro True Wireless ANC Earbuds User Manual

HAYLOU X1 Pro True Wireless ANC Earbuds

Overview

How to Wear

Please adjust earbud to fit yourself best.

When calling, adjust Mic 1 towards mouth to gain better talking experience.

How to Charge

1. Fully charge the charging case and earbuds before first use.
2. Insert the charging cable to simultaneously charge the earbuds and the charging case.
3. Earbuds: Put them back into the case, the earbuds indicator light is solid red. After fully charged, the indicator light is solid white for 60s and then goes out.

Battery Indicator of Charging Case

Open/close the lid, the actual battery level will be displayed after three lights flash 3 times. When the battery is greater than 30%, the battery indicator will be on for 10s and then go out.
(You need to close the case first then open to check battery level display again)

Low Battery Prompt of Charging Case:
Less than 30%, LED1 flashes 3 times every 2s, and goes out after 1 minute of continuous circulation.

Power-on

When the earbuds are in the charging case, open lid to power on.
When the earbuds are outside the case and in power-off state, long press the MFB button for about 1.5s to power on.

Power-off

Put earbuds back into case and close the lid, they will automatically power off.

How to Connect

Take out both earbuds from the case simultaneously. Open device Bluetooth, search for “Haylou X1 Pro” and click to connect.
If connection fails, put earbuds back into case and try again. After connection, earbuds will automatically re-connect to the last-paired device whenever powering on (Bluetooth needs to be turned on).

Switch Between Mono and Stereo Mode:
Pick up two earbuds to auto enter stereo mode and push one back to enter mono mode.
Or you can pick it up again to resume stereo mode.
Manual Connection: When earbuds are turned off, manually turn on the two earbuds.
Wait 2-3s for the earbuds to turn on and connect with each other. When indicator lights on both earbuds flash white slowly, turn on device Bluetooth to connect.

How to Use

• Click MFB Button
  Play/Pause music

• Click MFB Button
  Answer/End call

• Double Click MFB Button on L
  Skip track backward

• Double Click MFB Button on R
  Skip track forward

• Long Press MFB Button for About 4s Switch ANC Mode
  Triple click MFB button on R

• Turn on/off Low Latency Mode
  when standby

• Triple Click MFB Button on L
  Summon voice assistant when standby

Factory Setting

If the earbuds cannot be connected and used normally, please refer to the following methods: When the earbuds are in the charging case and the charging case has power, long press MFB button for 10s, the earbuds will automatically be reset (the connection records between the two earbuds and device will be cleared).

• If the operation fails, please repeat the above steps; or log in to the official store, contact customer service to view the reset operation video.

Audio only Outputs from Single Earbud

It’s unusual indeed, please set earbuds to factory, remove connectivity record on phone and reconnect.

Other Charging Problems

1. White LED turns off after 1 minute. It means your earbuds have been fully charged.
2. The earbuds won’t be charged if the charging case is out of power.
3. LED does not turn on when charging the case. It means that the case has been fully charged so the light does not turn on.

Package List

Earbuds, charging case, 3 pairs of ear tips (M size has been pre-installed), charging cable, user manual.

Basic Parameters (Earbuds)

• Operation Range: 10m (open space with no obstacle)
• Battery Capacity: 45mAh (single earbud)
• Charging Time: Approx. 2hr
• Talk Time: Approx. 5hr
• Standby Time: Approx. 60hr
• Input Parameter: 5V 100mA
• Battery Type: Rechargeable li-ion Button Battery
• Bluetooth Version: V5.2

Basic Parameters (Charging Case)

• Input Parameter: 5V 500mA
• Output Parameter: 5V 150mA
• Charging Time: Approx. 3hr
• Battery Capacity: 400mAh
• Battery Type: li-ion Polymer

Caveats

Warning

1. Do not disassemble, repair or modify the product for any reason, as this may cause fire or even completely destroy the product.
2. Do not expose the product to environments where the temperature is too low or too high (below 0°C or above 45°C).
3. Keep the indicators away from the eyes of children and animals while using the earphones.
4. Do not use this product during thunderstorms. Thunderstorms may cause the product to malfunction and increase the risk of electric shocks.
5. Do not wipe and clean the earphones or their case with alcohol or other volatile liquids.
6. Avoid any contact with liquids.

Note

1. Please read this user manual carefully before using the product and please properly store it.
2. When using for the first time, please fully charge this product.
3. Please charge the product, in case it has not been used over two weeks.
4. Please use certificated charger.
5. Do not wear earphones for a long term to protect your hearing.
6. Do not wear earphones in any situations with potential risks as wearing them may reduce your perception to the outside world.

Daily Maintenance

Please do not shower with earbuds. Do not wear them in rainy day. Do not leave them in washing machine or other extreme situations. Clean them with dry cloth.

Warranty Card

Warranty Period

12 months after you purchase this item. (or you may inquire your local shopper for more details.)

Free Service

Supposing any defects caused by quality issues occur within the warranty period, please take this warranty card and purchase receipts to your distributor for free exchange service.

Model Number|
---|---
Date of Purchasing|
User’s Name|
User’s Phone|
User’s Address|
Shop’s Name|
Shop’s Address|
Comments|

Free exchange service will not be accessed under following circumstances:

1. Damages caused by unauthorized disassembly.
2. Defects or physical damages caused by leaking or dropping off.
   Damages by act of God.
   Supposing your item is within any damages or defects except the above circumstances, please return to us or your distributor for free repairing.

FCC Requirement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference;
2. This device must accept any interference received, including interference that may cause undesired operation.

Manufacturer: Dongguan Liesheng Electronic Co., Ltd.
Address: Room 401-410, Building 1, No. 86 Hongtu Road, Nancheng District, Dongguan City, Guangdong, China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>