HOOKE ROAD BXG.2090-S Windshield Frame Cover Armor Set Installation Guide
- June 1, 2024
- HOOKE ROAD
Table of Contents
MAKE A DIFFERENCE
Windshield Frame Cover Armor Set
BXG.2090-S
Contents:
| Qty | Part Name | Size(mm) | Picture |
|---|---|---|---|
| 14 | Button Head Socket Cap Bolts Screws | M8*16 | |
| 12 | Button Head Socket Cap Bolts Screws | M8*25 | |
| 26 | Flat Washer | M8201.5 | |
| 14 | Flange Hex Lock Nuts | M8 |
Tools required:
a. Drive Socket Ratchet Wrench;
b. 5mm Hex Bit Socket;
c. 13mm Wrench;
d. 13mm Shallow Socket;
Installation time:
About 1 hour, 1-2 people may be needed. Installation time may differ according
to your mechanical skill level.
(PLEASE VERIFY ALL PARTS ARE PRESENT AND READ INSTRUCTIONS CAREFULLY BEFORE
STARTING INSTALLATION!)
To view the electronic version (BXG.2090-S), please scan the QR code.
https://drive.google.com/drive/folders/13DsgtfdEff6zxy6_QfplO3CN5jTJJAbi?usp=sharing
Installation instruction:
Step 1: In order to install our product, you should remove the factory A-pillar trim first and preparing for installation.
Step 2: First, assemble it into one piece on the ground. To assemble the frame
cover (A) & (B). Use the button head socket cap bolts screws (M816), Flat
Washer (M820*1.5), Flange Hex Lock Nuts (M8).
(4) M816 Button Head Socket Cap Bolts Screws
(4) M820*1.5 Flat Washer
(4) M8 Flange Hex Lock Nuts
Step 3: To assemble the frame cover (C) & (D). Use the button head socket cap bolts screws (M816), Flat Washer (M820*1.5), Flange Hex Lock Nuts (M8). Don’t tighten up those bolts.
(6) M816 Button Head Socket Cap Bolts Screws
(6) M820*1.5 Flat Washer
(6) M8 Flange Hex Lock Nuts
Step 4: To assemble the two part (the step 2 & step 3). Use the button head socket cap bolts screws (M816), Flat Washer (M820*1.5), Flange Hex Lock Nuts (M8).
(4) M816 Button Head Socket Cap Bolts Screws
(4) M820*1.5 Flat Washer
(4) M8 Flange Hex Lock Nuts
Step 5: After assembling it into one piece on the ground, insert the mounting bracket (A) & (B) into the factory vehicle hole of the A-pillar trim and install it with the factory bolts. (Picture is shown passenger side)
Step 6: Lift the assembled product into the vehicle, taking care to avoid scratching the car, and it is advisable to have two people install it together.
Step 7: Adjust the product’s hole positions from left to right, aligning them with the vehicle’s original mounting holes and the mounting bracket holes. If necessary, you can use tools for adjustments. Tighten up the the button head socket cap bolts screws (M816), Flat Washer (M820*1.5). At last, tighten up the step 3 bolts.
Step 8:
The installation is complete. We hope you enjoy a wonderful off-road life with
this quality Hooke Road product!
Attention:
- The product parts in this instruction may differ slightly from the actual product contents but generally does not affect the installation of the product.
- Please feel free to contact your distributor if you have any kind of question about your purchase.
Hooke Road to find your parts.
Feel Free To Share Your Vehicle @Hooke Road 4×4
With The Hashtag #hookeroad If You’d Like