Roinvou C7291 For Toyota Sienna 2011 2013 User Guide
- June 1, 2024
- Roinvou
Table of Contents
Roinvou C7291 For Toyota Sienna 2011 2013
Product Information
Specifications
- Product Name: Central Control for Toyota Sienna 2011-2013 / C7291
- Compatibility: Toyota Sienna 2011-2013 models
- Tools Required for Disassembly: Wires, Protocol box, Installation tools
- After-sales Support: Contact via email at [email protected]
- FCC Compliance: Part 15 of FCC Rules
Product Usage Instructions
Disassembly
- Turn counterclockwise to unscrew the gear lever handle.
- Use a pry bar to open the frame beneath the central console and the bottom plate beneath the gear lever.
- Pry out the air conditioning control panel and unplug the wires connected to the original car radio.
- Unscrew the four screws beneath the original car radio and disconnect the attached wires.
- Unscrew the four screws of the air vent from the original car radio panel, remove the air vent, and take out the clips securing the original car radio.
Pre-installation Preparation
Before starting the replacement job, gather tools such as a plastic pry tool and a screwdriver. Ensure the car’s power is cut off during installation.
Installation
- Secure the air vent onto the new radio panel, tighten the screws, connect wires, and install the new radio back into position.
- Connect wires between the air conditioning control panel and the original car, reinstall it, and install the bottom plate of the gear lever.
- Reinstall the frame beneath the central console and tighten the gear lever handle. The installation is complete.
FAQ
Q: What should I do if the wiring harness does not match during installation?
A: If the wiring harness does not match, please contact customer service to request the correct wiring harness for compatibility.
Q: How can I get assistance if I encounter problems during installation?
A: If you encounter installation problems or have questions after reading the manual, contact us via email at [email protected]. We aim to respond within 24 hours to assist you with any issues.
For Toyota Sienna 2011-2013 / C7291
Central Control Disassembly and Operation Post-installation rendering
TOOLS REQUIRED FOR DISASSEMBLY
- Wires
- Protocol box
- Installation tools
Disassembly
- Turn counterclockwise to unscrew the gear lever handle. Use a pry bar to pry open the frame beneath the central console, then pry open the bottom plate beneath the gear lever.
- Pry out the air conditioning control panel and unplug the wires connected to the original car. Unscrew the four screws beneath the original car radio.
- Take out the original car radio and disconnect the attached wires.
- Unscrew the four screws of the air vent from the original car radio panel, then remove the air vent. Take out the two clips securing the original car radio.
PROPOSE
Before starting the replacement job, you should prepare tools such as a plastic pry tool and a screwdriver, and make sure the car’s power is cut off during the installation.
Installation
(If the wiring harness does not match, please contact customer service to request the correct wiring harness)
- Secure the air vent onto the new radio panel and tighten the four screws on both the left and right sides.
- Connect the wires between the new radio and the original car, and connect the protocol box.
- Install the new radio back into its designated position.
- Connect the wires between the air conditioning control panel and the original car, and reinstall it back into the original position. Install the bottom plate of the gear lever.
- Reinstall the frame beneath the central console to its original position, and tighten the gear lever handle in a clockwise direction. The installation of the new radio is complete.
COMPARISON
Effect of Installation
GENTLE REMINDERS
- Due to the complexity of the product structure, you may encounter some problems during installation.
- If you still have any questions about the installation after reading this manual, you can contact us and we will respond to you within 24 hours.
- Don’t worry; we will do our best to solve the problem for you until you are satisfied.
- After-sales email: [email protected]
FCC
WARN FCC WARNING
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation