ORAIMO OHP-610 S Wireless Headset User Manual

May 15, 2024
oraimo

User Manual

PACKAGE CONTENTS

ORAIMO OHP 610 S Wireless Headset - PACKAGE

PRODUCT OVERVIEW

ORAIMO OHP 610 S Wireless Headset - Overview

  1. Button + (Volume Up / Last Track)
  2. Button O (Play/Pause/Call)
  3. Button – (Volume Down / Next Track)
  4. Power Switch
  5. Microphone
  6. 3.5mm AUX Input
  7. LED Indicator
  8. Type-C Charging Port

USING YOUR HEADSET

  1. Power on / off
    Toggle the power switch to power on/off. LED Indicator| Status
    ---|---
    | Steady blue for 1 second with voice prompt saying “power on”| Power on
    | Steady red for 1 second with voice prompt saying “power off”| Power off

The headset will automatically turn off after 5 minutes if no device is connected.

  1. Pair with your device
    When power on, the Headset will enter pairing mode automatically. Open the Bluetooth function and connect the Bluetooth named as oraimo BoomPop2S on your device to finish the pair.ORAIMO OHP 610 S Wireless Headset - Using
1
LED Indicator Status
Fast flashing blue with voice prompt saying “pairing” Enter pairing mode
Steady blue with voice prompt saying “connected” Connected to a device
  1. How to connect to another device
  1. Disconnect the Bluetooth connection with the last device:
    a. Disconnect directly from your device.
    b. Or press the button + and button – simultaneously for 3 seconds.
  2. Enter the pairing mode to achieve the connection again.
    Make sure the distance of the headset and your device is less than 1 meter / 3.3 feet at the first time of connection.
    The headset will automatically connect to the last connected device if available.
    If not, the headset will enter pairing mode.
  1. Connected via AUXORAIMO OHP 610 S Wireless Headset - Using 2 The speaker will enter AUX mode once the cable is plugged in.
    (Mic will be banned when using AUX mode)

  2. Charge your HeadsetORAIMO OHP 610 S Wireless Headset - Using 3
    | LED Indicator| Status
    ---|---|---
    | Quickly flashing red with voice prompt| Low battery
    | Slowly flashing red| Being recharged
    | Light off| Fully recharged

Use the attached Type-C cable to charge the headset.
The headset will automatically power off when being charging.
Control by gestures
1. Raise your hand from the front and touch the right headset directly to confirm its position.
2. Move your hand slightly to the right and about 6 cm away to start the gesture controls by fingers as below pictures.

ORAIMO OHP 610 S Wireless Headset - Using 5 Gesture controls only work on the right side of the headset.

  1. Control by buttons

●| Play/Pause| Short press once
+| Volume up| Short press once
Last track| Long press for 1 second
| Volume Down| Short press once
Next track| Long press for 1 second
●| Answer/End a call| Short press once
Reject a call| Long press for 1 second
Answer/End a third-party call| Short press once
Reject a third-party call| Long press for 1 second
Switch between two calls
(After connecting to a third-party call)| Long press for 1 second
Others
+-| Disconnect and re-enter pairing mode| Long press for 3 seconds
●| Reset
(While the headset is being charged)| Long press for 3 seconds

BASIC PRODUCT SPECIFICATIONS

Bluetooth Version V5.3
Bluetooth Range ≥ 10m
Speaker Diameter 40mm
Battery Capacity 500mAh
Charging Time 1.5 hours
Playtime Up to 50 hours
Supported Format Mic Support / Aux-in Mode / Type-C

ATTENTION

  1. To preserve battery lifespan, fully charge at least once a month
  2. Use original or certified cables
  3. Do not expose to liquids
  4. Do not disassemble
  5. Avoid dropping
  6. Avoid extreme temperatures
  7. Do not use the product outdoors during a thunderstorm
  8. Do not use any corrosive cleaner/oil to clean

TROUBLE SHOOTING

Problem Description Cause Solution
Power on function fails. The battery is exhausted. Use the charger kit to

fully recharge the battery.
The power switch is not fully toggled.| Toggle the power switch again.
Recharging function fails.| The recharging port is not properly connected.| Reconnect the charging port.
The headset cannot be searched or pairing fails.| The headset does not enter into the pairing mode.| Turn on the headset again to enable it enter into the pairing mode.
The headset is connected by other device.| Long press button + & button – at the same time for 3 seconds to disconnect with the device and re-enter pairing mode.
The Bluetooth function of the device is in error.| Restart the device and the Bluetooth and then pair with the headphone again.
Gesture control is unresponsive.| The distance of the gesture operation exceeds the optimal sensing zone.| Please raise your hand from the front and touch the right headset directly to confirm its position. Move your hand slightly to the right and about 6cm away (approximately the size of a fist) to start the gesture control.
The gesture control poses are not standardized.| 1. The gesture swing angle is about 60-90 degrees, with a time interval of about 0.5s between two operations;
2. The gesture swing needs to be completed fully twice untilyou hear a beep sound.
3. Please use your fingers to operate.

CONSIDERATE HINTS

  1. Do not turn up the volume to a fair high level constantly as this could shorten the service life of this product or impair your hearing.
  2. When encounter any fault during operation, please cut off the power supply and disconnect the USB cable to prevent further damage to the product or other components.
  3. The wireless transmission range or connectivity could be affected by low battery power. In that case, please recharge immediately.

FCC Caution:
Labeling requirements.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference received, including interference that may cause undesired operation.

Information to user.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment information to the user.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by tuming the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Note: This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.
RF Exposure Statement
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Device types: OHP-610S (FCC ID: 2AXYP-OHP-610S)

Wireless Headset
Model: OHP-610S
Hereby, ORAIMO TECHNOLOGY UMITED
Declares that this Wireless Headset is in compliance with the essential requirements and other relevant provisions of directive 2014/53/EU.

CAUTION

  1. Use careful with the earphone maybe excessive sound pressure from earphones and headphones can cause hearing loss.

  2. Risk of explosion if battery is replaced by an incorrect type, dispose of used batteries according to the instructions.
    – disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion;
    – leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas;
    – a battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.

  3. The product shall only be connected to a USB interface of version USB 2.0.

  4. EUT Temperature: 0C ~+45 C (Standalone).0 C ~+40 C (with adapter).

  5. To prevent possible hearing damage, do not listen at high volume levels for long periods.

  6. USB cable is shielded.
    Frequency Range(RF):
    BT: 2402-2480MHz (TX/RX);
    Max RF output power :
    BT(BDR): 2.70dBm
    BLE: 2.48dBm

High sound pressure with hearing damage risk.
Do not listen at high volume levels for long periods.

EU DECLARATION OF CONFORMITY
in accordance with
Annex VI of Directive 2014/53/EU of the European Parliament and of the Council

  1. For the following Radio equipment: Model: OHP-610S, Product: Wireless Headset, Trade name or Brand: oraimo Software / Hardware number. V015/ V02

  2. Name and address of the manufacturer or his authorized representative.
    Manufacturer: ORAIMO TECHNOLOGY LIMITED
    Address: FLAT N 16/F BLOCK B UNIVERSAL INDUSTRIAL CENTRE 19-25 SHAN MEI STREET FOTAN NT HONGKONG

  3. This declaration of conformity is issued under the sole responsibility of the Manufacturer.

  4. Object of the declaration (identification of the radio equipment allowing traceability; it may include a colour image of sufficient clarity where necessary for the identification of the radio equipment):

  5. The object of the declaration described above is in conformity with the relevant Union harmonization legislation: Directive 2014/53/EU (RED)

  6. References to the relevant harmonised standards used or references to the other technical specifications in relation to which conformity is declared:
    Article 3.1a Health:
    EN 62479:2010
    Article 3.1a Electrical Safety:
    EN62368-1:2014+A11:2017
    EN IEC 62368-1:2020+A11:2020
    Article 3.1b:
    ETSI EN 301 489-1 V2.2.3 (2019-11)
    ETSI EN 301 489-17 V3.2.4 (2020-09)
    Article 3.2:
    ETSI EN 300 328 V2.2 2 (2019-07)

  7. Notified Body Name: Eurofins Electrical and Electronic Testing NA, Inc.
    Notified Body Number. 0980
    Notified Body Assessment Performed: Module B/C on Article 3.1a, 3.1b, 3.2
    Technical File Identification Number: N/A

  8. Where applicable. description of accessories and components, including software, which allow the radio equipment to operate as intended and covered by the EU declaration of conformity: User instructions are provided in the User Manual. The Software and Hardware versions are specified above.

  9. Additional information:
    Referring to Article 10.2 of the Directive, this equipment is so constructed that it can be operated in all Member States, without infringing applicable requirements on the use of radio spectrum.
    Referring to Article 10.10 of the Directive, there are no restrictions on putting this equipment into service or of requirements for authorisation of use. Please refer to the User Manual for details.
    On behalf of:
    Manufacturer. ORAIMO TECHNOLOGY UMITED
    Address: FLAT N 16/F BLOCK B UNIVERSAL INDUSTRIAL CENTRE 19-25 SHAN ME! STREET FOTAN NT HONGKONG (place and date of issue):Shenzhen, 2023-08-25
    (name, function): Nengyong.Wu/ Manager.
    (signature):
    (Name and signature of person responsible)

CUSTOMER SERVICE

365 DAYS WARRANTY

Email:

India: care@oraimo.com
Nigeria: care.ng@oraimo.com
Kenya: care.ke@oraimo.com
Ghana: care.gh@oraimo.com
Morocco: care.ma@oraimo.com
Egypt: care.eg@oraimo.com
South Africa: care.za@oraimo.com| Cameroon: care.cmr@oraimo.com
Tanzania: care.tz@oraimo.com
UAE: care.ae@oraimo.com
Ivory Coast: care.ci@oraimo.com
Brazil: care.br@oraimo.com
Colombia: care.co@oraimo.com
Others: service@caricare.com
---|---

  1. All quality-related defects on items sold directly by oraimo or oraimo’s authorized resellers are covered by an extensive warranty, starting from the date of purchase.
  2. oraimo’s limited warranty is restricted to the country of purchase. The limited warranty is void on items taken outside the country they were originally bought in or shipped to directly from an authorized online purchase.
  3. This warranty covers only original oraimo products. It is not applicable to normal wear and tear, or any defects arising from damage caused by misuse of this product.
  4. Warranty is for the primary product only nor transferable. Any free additional product(s) are not covered in this warranty.
  5. If the product fails regardless of usage in compliance with the instruction manual and other written precaution, replacement will be provided free of charge.
  6. To receive replacement, bring the warranty certificate and the product itself to the store from where you have purchased the product.

WARRANTY CERTIFICATE

Name:|
---|---
Address:|
Tel. No.:|
Date of purchase(dd/mm/yy):|
Store name:|
Warranty period:|

WELCOME GUIDE
BoomPop2S | OHP-610s |

  • For safety issue, the product remains low capacity during shipping.
    Please fully charge the product before initial use!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals