Lightology P472 Wall Mount Fixture Instruction Manual

: June 9, 2024
: Lightology

Table of Contents

READ AND SAVE THESE INSTRUCTIONS
PREPARATION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

P472 Wall Mount Fixture
Instruction Manual

READ AND SAVE THESE INSTRUCTIONS

WARNING ! SHUT POWER OFF ATFUSE OR CIR CUITBR EAKER .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
MOUNTING THE FIXTURE (Fig.1)

Shut off the power at the circuit breaker and remove the old fixture, including the mounting hardware.
Carefully remove the fixture from the carton and check that all parts are included as shown in the illustration.
Attach mounting plate (A) to the junction box with mounting screws (B) (Size: #8-32N*L0.5”).
CONNECTING THE WIRES (Fig. 2)
Connect the electrical wires as shown in Fig. 2, making sure that all wire connectors are secured. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the circular strap using the green screw provided.
FINISHING THE INSTALLATION (Fig.1)
Align fixture body (D) to mounting plate (A) and secure it with screws (C).
Place shade (E) over the socket and level horizontally.
Install light bulbs (not included) in accordance with fixture specifications, (DO NOT EXCEED THE MAXIMUM WATTAGE RATING!) (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)
Your installation is now complete. Return power and test the fixture.

Note: Illustration (Fig.1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.
IMPORTANT: FIXTURE SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN TO ENSURE PROPER WIRING AND INSTALLATION.

PREPARATION

Shut off power at the fuse box or circuit breaker box. If necessary. Remove the old fixture and mounting hardware.
Carefully unpack your new fixture and lay out all the parts on a clear area. Take care not to lose any small parts necessary for installation.
MOUNTING THE FIXTURE (FIG. 1)
Secure mounting back plate (A) to the outlet box using junction box screws (B) (Size: 8-32*1/2”L). Theside of the mounting back plate marked “GND” must face out.
CONNECTING THE WIRES (FIG. 2)
At this point, connect the electrical wires as shown in Fig. 2, making sure that all wire connectors aresecured. If your outlet has a ground wire (green or bare copper), connect the fixtures ground wire to it. Otherwise, connect the fixture ground wire directly to the mounting plate (A) using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
Align fixture’s back plate (C) onto mounting back plate (A) and secure with screws (D) (Size：’M4*8MM).
FINISHING THE INSTALLATION (FIG.1)
Align diffuser (F) followed by gaskets (O), onto bracket (I) and secure with screws (G). The clear side diffuser (F) should face down toward bracket (I).
Align cloth shade (H) (PS472) onto back plate (C) and secure with screws (E)
CAUTION/ATTENTION: When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base or front bracket (I) only.

IMPORTANT: Fixture should be installed by a qualified electrician to ensure proper wiring and installation.
Replacing LED module (Fig. 3)
The LED module can be replaced by a qualified electrician without cutting of wire and without damage to any decorative element to which the fixture is attached. See installation steps for more details (Fig 3.)
a. Shut off the power.
b. Remove screws (E) and cloth shade (H) from back plate (C).
c. Remove screws (D) and carefully separate the fixture from mounting back plate (A).
d. Remove the wire nuts (L) located inside the fixture back plate to disconnect the LED module.
e. Remove screws (J) from mounting plate (A).
f. Remove screws (K) on heat sink (N). Carefully remove the LED module (M) from the heat sink (N),
g. Reverse steps b-f for installing the new LED module.
h. Note: The LED module should be provided by a specified supplier.
i. For better heat dissipation the LED module (M) should be applied with thermal grease when re-lamping. IMPORTANT: Fixture should be installed by a qualified electrician to ensure proper wiring and installation. Dimmable with ELV and/or LED compatible wall dimmer switches.

american lighting assocaltion