Shenzhen Fujikam Intelligence 871 Cloud Camera Installation Guide
- June 5, 2024
- Shenzhen Fujikam Intelligence
Table of Contents
Cloud Camera
Quick Installation Guide
871 Cloud Camera
Prompt: Our APP will be in continuously updated for a better user experience.
The actual operation interface may not accordance with this manual, please
operate according to APP.
1. Instal MIPC APP
The method I: Download MIPC APP in: http://www.mipcm.com/download
Method II: Scan the QR code with the phone to download the MIPC app.
Method III: Download the `MIPC’ APP from APP Store(i0S) or Play Store
(Android).
2. Register an Account
Open the ‘WPC’ APP, click the ‘sign up button, register an account as
required, bind an email then log in
3. Add Device
-
Click the
+’ in the upper left corner of the device list, selectBattery Cam’; -
Please switch the power to OFF and then ON; Wait for the light to turn on and click ‘Next’. Note:
1. Press the RESET button for 1 second to enter the Wi-Fi configuration mode; Long press for more than 10 seconds to restore the factory settings (Hearing the corresponding voice means the setting is successful);
2. If theWiFi Connection’ configuration fails, you can tryQR Code Connection’. -
Click the RESET button at the camera bottom, after hearing the prompt ‘Waiting for receiving the wireless config information’ the camera will enter the config mode. When you see the indicator fastly flashes then click ‘Next’ .
-
Scan the camera QR code, then config the camera
-
Connect the camera with a Wi-Fi router (Which only supports 2.4GHz), input the Wi-Fi password then click ‘Next’.
-
Please put the phone QR code in front of the camera lens, until you hear the prompt ‘Connecting to the router’, then go next.
-
When you hear the prompt `Config successfully’, it means to set up the Wi-Fi network successfully.
-
Set up a nickname for the camera, then click ‘Finish’.
FAQ
1. What if the camera cannot connect to Wi-Fi?
A: – Check if your Wi-Fi password contains special characters such as
spaces, commas, periods, etc. which may not be recognized by the camera.
– The camera is only available to 2.4GHz Wi-Fi, not 5GHz Wi-Fi. Please check
and see the Wi-Fi frequency band of the router.
– Keep your mobile phone as close to the camera as possible, and keep your
camera as close to the router as possible.
– Poor Wi-Fi signal may result in failure to connect to your camera. You can
use a Wi-Fi Range Extender which will extend the Wi-Fi signal and wireless
coverage of existing wireless networks.
– If you fail to connect the camera, please follow these steps and try again:
- Remove the power cord. Then, re-plug it in.
- Press and hold the RESET button for over 10 seconds to restore the camera to factory settings when you hear the voice prompt and the IR light turns on.
- Add the camera once more when you hear the voice prompt.
2. After inserting the SD card properly, why does the camera still not
have any recorded videos?
A: – The camera needs to be inserted when the camera is off
– After the camera is inserted with an SD card, the video recording function
can be turned on manually.
3. APP can’t receive the alarm notification?
A: The camera has motion detection and alarm function, but it needs a
manual setup. Steps: enter the camera ‘settings’, select `Notifications’,
enable the motion detection feature, and save the settings.
4. What if I forget my account & password?
A: You can find your account & password with the binding email, it will not be
found if not binding with the email.
5. How can I see the recorded video? Can I put the SD card on the computer
for playback?
A: For your privacy and security, video files are encrypted, they must be
playback through a mobile phone APP or computer APP, and they cannot be played
directly on the computer. You need to export the video through SDtool, a
special video export tool. The tool can be downloaded from
www.mipcm.com.
6. How does the camera restore to factory settings?
A: Press and hold the RESET button for 10 seconds, and you will hear the
voice prompt ‘Restore the factory settings successfully’, now the camera
starting to restore, it will finish about 10 seconds, then you will see the
indicator flashing quickly
FCC Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions (1)this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator & your body.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>