NOVY 70023 Lighting Shelf Pro User Manual

NOVY 70023 Lighting Shelf Pro

WARNING

• This product contains an ambient light source of energy efficiency class G
• This product contains a functional light source of energy efficiency class F
• Light source (LED only) and driver can only be replaced by a recognised installer.
• Provide an on-off switch at mains power supply.

Gesture Control Pro (GC Pro)

The Gesture Control Pro (GC Pro) is operated by multiple sensors. The sensors are located across the entire width at the bottom of the Novy Shelf Pro, behind the black sensor strip. To operate the Novy Shelf Pro, move your hands under this black strip. The sensors have a range of 15cm underneath the Novy Shelf Pro (see the grey shaded area in the image below).

To all movements made lower than 15cm, the sensors do not respon.

Switching the lighting on and off

The lighting can be activated in 2 ways:

1. Switch on the light across the entire width by moving your hand from left to right or right to left under the sensor strip.
2. A narrower beam is activated by holding your hand under the sensor strip for more than 1 second. The light beam will only be activated at the location of your hand.

Changing the light balance from top to bottom

Balance more towards the top

• Holding your hand closer to the sensor will move the light towards the top of the Novy Shelf Pro.

Balance more towards the bottom

• By holding your hand further from the sensor (but no further than 15cm!), the light will move towards the bottom of the Novy Shelf Pro.

Changing the width of the light beam

If required, the width of the light beam can be adjusted. By moving 2 hands under the sensor strip towards each other, you can make the beam narrower. By moving 2 hands away from each other under the sensor strip, you can make the beam wider.

Moving the light beam from left to right
Moving the beam is done by holding your hand under the beam and then moving the hand to the desired location of the beam. When doing so, keep your hand no more than 15 cm below the Novy Shelf Pro.

Another way to move the light beam is to hold your hand at the place under the sensor where you want to move the light beam. The light beam will then move towards your hand.

Changing the colour at the top

By holding your hand close to the sensor for 2 seconds, the light on the top side of the Novy Shelf Pro will change to a preset colour.

Setting the colour

If you want to change the colour of the mood setting, first go to the mood setting in the preset colour (hold your hand 2 seconds 1cm below the sensor). Then hold your hand under the sensor for another 3 seconds until the coloured light starts pulsing.

By moving your hand under the sensor, you “scroll” through the available colours. You can scroll forward and backward by moving the hand either from left to right or right to left underneath the sensor. When you have reached the desired colour, remove your hand. After 2 seconds, the pulsing will stop and the chosen colour will be set as the default colour.

Service

If there is a fault you can contact your (kitchen) supplier and/or Novy Customer Care Service

• Belgium Tel.: +32 (0)56 36 51 02
• France Tel.: +33 (0)3 20 94 06 62
• Germany Tel.: +49 (0)511 54 20 771
• The Netherlands Tel.: +31 (0)88 011 91 10
• Unite Kingdom Tel.: +44 (0) 207 866 2493
• For all other countries: your local installer or
• Novy in Belgium: +32 (0)56 36 51 02

To be able to deal with the fault promptly and efficiently it is necessary that the Novy Customer Care Service knows which type of appliance you have.

Installation

Before starting the installation, make sure that the voltage on the wiring to be used is switched off!

1. Determine the preferred position of the Novy Shelf Pro

   • Mark the preferred position of the Novy Shelf Pro on the wall and determine the height of the drill holes. Place the wall bracket against the wall and mark 1 drill hole.
   • Drill the first hole.

2. Draw/drill the wall bracket

   • Attach the wall bracket with 1 bolt and mark the remaining drill holes (level).
   • Drill the remaining drill holes.

3. Mounting the wall bracket
   Mount the wall bracket. When tightening the bolts, make sure the bracket remains flush.
   

4. In case of crooked walls (see wall bracket), resistance may occur between the wall and the shelf. Make sure the wall bracket does not warp against a hollow or convex wall. If it does, first fill the spaces behind the bracket using shims.

5. Wiring top/bottom
   If the wall socket is not located underneath the Novy Shelf Pro, make sure that when hooking in, the wiring leaves the Shelf on the side of the wall socket (depending on location of the wall socket). If the wiring/wall socket is next to the hanging bracket, connect the wiring before hooking in the Novy Shelf Pro.
   

6. Mounting the Novy Shelf Pro

   • Hang the shelf with the wiring in the wall bracket at a 30˚ angle as indicated in the drawing.
   • Before lowering the Novy Shelf Pro into a horizontal position, dispose of the excess power cord in the cavity at the back of the shelf. Once the Novy Shelf Pro hooks into the bracket and the wiring is concealed, lower the shelf until it hangs horizontally.
     

7. Conceal the wiring
   If the wall socket is located above or below the Novy Shelf Pro, the wiring can be concealed at the top/bottom using the special recess at the back/ top of the Novy Shelf Pro if required

8. Connect the wiring
   Connect the wiring of the Novy Shelf Pro to the wall socket. If the power source is a power plug socket, first mount a plug to the Novy Shelf Pro’s wiring. Make sure you have enough length to reach the power plug socket.

9. Turn the power on
   CAUTION: When switching on, the sensor will automatically calibrate itself. Make sure there are no objects less than 15cm below the Novy Shelf Pro. This may interfere with the calibration.
   NOTICE! use of a light switch should preferably be avoided. If desired, the Novy Shelf Pro can also be connected to a light switch. If a switch is used, the lighting will not respond to hand signals when it is not powered.

External factors affecting the operation

The Novy products operate with infrared sensors. If there is an extraordinary amount of infrared light, in the immediate vicinity of the fixture, this may adversely affect operation:

• Bright sunlight reflecting off shiny objects.
• Direct radiation from halogen spotlights or incandescent lamps at the underside of the fixture.

In case of excessive amounts of steam, the light fitting will possibly recognise this as a hand signal!

Cleaning
The fixture can be cleaned using simple soapy water. Do not use excess water. For removing stubborn stains, we recommend using a mild degreaser. Preferably use a microfibre cloth.

CAUTION: Cleaning the black sensor film should be kept to a minimum to avoid scratch formation. Scratches on the foil can negatively affect the operation of the sensors. Clean film with a microfibre cloth at all times.

NOVY nv reserves the right at any time and without reservation to change the structure and the prices of its products.

NOVY nv
Noordlaan 6
B – 8520 KUURNE

• Tel. 056/36.51.00

• Fax 056/35.32.51
  novy@novy.com
  www.novy.com

• United Kingdom: +44 (0)207 866 2493

References

• Specialist in cooker hoods and hobs | Novy - Novy

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>