42110 Hob Hood Novy Panorama 120 Pro Instruction Manual

42110 Hob Hood Novy Panorama 120 Pro

Product Specifications

• Model Numbers: 42110 Novy Panorama 120 Pro 4 zones, 42120 Novy Panorama 120 Pro 5 zones
• Part Number: 110153 MA1

Product Information

Installation Instructions

• Carefully read these instructions before installing and commissioning the hood.
• Symbols are used to indicate important tips or dangerous situations.

Product Usage Instructions

Safety Precautions

• Ensure that the power circuit is switched off before connecting the unit.

Mounting Tips

• Refer to the mounting drawings before starting the installation.
• Follow the provided mounting tips.

FAQ

Q: Where can I find the mounting drawings?

• A: The mounting drawings can be found on page 4 of the installation instructions.

Q: What should I do before starting the installation?

• A: Make sure to read and understand all the provided mounting tips and safety precautions.

GENERAL INFORMATION

General

• These are the mounting instructions for the Novy hood shown on the cover.
• The user manual is a separate booklet that is supplied with the hood.
• Carefully read these instructions before installing and commissioning the hood.
• Many symbols are used in these mounting instructions. The meanings of these symbols are given below.

Safety

• Observe the following mounting and safety tips for mounting.
• The installation and electrical connection of the unit shall be carried out by an authorized expert.
• The manufacturer does not accept any responsibility for any damage resulting from faulty building or connection.
• Check if all mounting materials have been supplied using the drawings.
• The unit is intended for household use only (preparation of food) excluding any other domestic, commercial, or industrial use.
• Safety can only be guaranteed if the unit is connected to an earth wire by the required regulations.
• Do not use an extension cord to connect to the electricity grid.
• Replace defective or damaged parts only with original Novy parts.

Important before mounting

• these mounting instructions show the mounting drawings.
• Observe the following mounting tips before starting the mounting activities:
• For easier mounting of the hood, it is recommended to do this with at least 2 persons.
• The housing of the unit to be mounted has the right dimensions.
• Make sure that the power circuit to which the unit is connected is switched off.

PARTS

Dimension

INSTALLATION INSTRUCTION

• Make sure that the power circuit to which the unit is connected is switched off.
• Check that all the hood accessories are present in the packaging.
• Check that all the hood parts are present in the packaging.
• Warning: pick up the hood only at the frontside to prevent glass damage to the hood.
• Check that all the hob parts are present in the packaging.
• Built-in height G≥ 760mm surface mounting: Make cut-out in bottom plate cabinet
• Built-in height G≥ 760mm flushing mounting: Make cut-out in bottom plate cabinet
• Built-in height G < 760mm
• When the height cabinet + worktop < 760mm, a cut-out in the bottom plate of the cabinet needs to be performed to install the cooker hood.
• To install the cooker hood kit 1821.400 can be used. Follow the steps described in the corresponding installation manual of the extension kit and then continue back from step 8.
• Measure the height left (Y1) and right (Y2) from the hob base plate to the supporting surface. Surface mount (L) = Top worktop surface.
• Flush mount supporting (R) = Milled edge in worktop.
• Set the height (Y) with the leveling feet, and measure from the top surface of the hood to the underside of the leveling feet.
• Measure the height (V) from the underside of the hood to the underside of the leveling feet (needed for vertical bend).
• Secure the leveling feet with the wrench 17. Measure the height (Q) from the base plate to the ground position.
• Cut the vertical bends to size X = (V+Q) -5mm. Slide the vertical bends into the outlet piece below the hood.
• Make sure that the hood guides are fully inward and secure this position.
• Lift the hood through the worktop cut-out in the housing.
• Warning: hold the hood only on the outside to prevent the glass from breaking.
• Warning: this activity is best done by 2 people.
• Place the positioning guides (42120035) between the worktop cut-out and the hood. Position the side and rear edge of the hood against these two guides.
• Set the bolt to the center of its range to make fine adjustments of the hood possible later. Slide the hood guides fully against the side wall of the housing.
• Slide the mounting brackets between the bolt and the lock nut of the guide until they are in the center of the groove.
• Secure this position with the screws supplied. Perform this action on both the left and right.
• Secure the position of the guides with the black screws
• Level the hood at both the left and right by moving it forward or backward at the bottom.
• Use a short spirit level (≤ 30cm) and place this on the marked places.
• Secure the position of both leveling feet in the housing with the plates n° 1821043 and screws n° 1821153.
• Adjust the position as necessary with the adjusting bolts on the guides.
• The positioning guides must be positioned with minimal clearance between the worktop cut-out and the hood.
• Remove the positioning guides.
• Warning: Carry out the following action carefully to avoid glass damage.
• Check the height of the cooker hood with a ruler, it MUST be leveled with the worktop (surface) or milled edge (flushing).
• Adjust if necessary with the leveling feet.
• Apply the waterproof tape 2mm from the rim to the underside of the hob glass.
• If necessary, remove a central piece of the tape from the back of the hob if it is not completely flat at the back during installation.
• Place the induction hob on the hood. Make sure the edge of the cut-out in the induction hob glass is aligned with the side profiles of the tower.
• Do not apply sealant between the bottom side of the hob and the worktop.
• Carefully place the upper glass with the pins in the cut-outs provided in the hood.
• Perform the above action carefully to prevent glass damage and scratches.
• Surface mounting: Adjust the position of the induction hob until the spacing around the tower top glass and cut-out is even.
• Flushline mounting: Adjust the position (front, back, left, and right) of the cooker hood until the spacing around the tower top glass and cut-out is even. (STEP 18, 21)
• Secure the position of the hob on the hood with the 6 screws n° 1821247.
• Tighten these bolts only finger tight, do not use a hand-held screwdriver.
• Adjust as necessary the height of the tower to the top of the hob.
• Turn the bolt with a wrench 10 counter-clockwise to raise the tower and clockwise to lower it.
• Connect first the hob cable connector to the hood.
• Hood: connect the plug to the mains supply.
• Hob: connect the hob’s power cable according to the relevant connection diagram.
• Optionally, the hob can be set with a power limit, see chapter “Power limitation induction hob”.
• Recirculation built-in box option: connect the in-built box to the hood outlet, if necessary, use optional fittings.
• Outlet with wall outlet grille option: use optional fittings to make the connection with the duct work possible.
• Switch the unit power supply circuit on.
• Keep the knob pressed for 3 seconds.
• If the 4 LEDs on the control flash directly, the safety system of the tower is activated.
• You can manually turn the tower up using a flat screwdriver.
• Carefully remove the top glass from the tower and place the screwdriver in the provided recess of the spindle in the center of the tower.
• Now turn the tower fully up until the safety switch as in step 36 is visible.
• The tower now moves to its highest position (30 cm).
• Remove the safety sticker from the tower. The 4 LEDs on the controller flash.
• Slide both lower collection trays into the hood with the short side (K) facing forward n° 42120039.
• Place the collection security n° 42120026 in the hood. They should be positioned against the center of the tower.
• Slide both upper collection trays n° 1821107 into the hood.
• Place both grease filters in the hood on the fall protection.
• Verify the correct placement of the grease filters using the positioning tab.
• Place the front glass on the hood tower.
• Position the tabs of the glass in the cut-out in the tower and tilt the glass toward the magnets until the glass snaps into place.
• Press the knob to re-initialize the tower.
• The tower now moves to the closed position.
• Recirculation: The device is set in recirculation mode by default.
• Duct out: set the device in duct out mode by pressing the key combination “+” and “-” for 3 seconds.
• The lead next to will blink 3x to acknowledge the setting.
• Repeat these actions for recirculation mode, the LED will be on for 3 seconds.
• OPTIONAL: Installation I/O module n° 990036 Remove the cover from the connection connector.
• Plug the I/O module connection cable into the connector. (See manual 990036 I/O module)

POWER LIMITATION INDUCTION HOB

Power limitation induction hob

• The hob is equipped with a power limitation. If the power level on two zones exceeds the maximum power, the last selected cooking zone will be maintained, and the other cooking zone will be automatically reduced.
• The display of this zone will flash first, then the level is automatically reduced to the highest appropriate position.
• This restriction is set at the factory to 7400W (32A) on the 4 zones hob reference 42110 and on 10400W (48A) for the 5 zones hob reference 42120.
• This power limit can be adjusted if required.

Configuration procedure:

• Make sure there is no more pot on the hob
• Disconnect the appliance from the grid by removing the fuse or turning the circuit breaker off.
• Reconnect the table to the grid
• Start the procedure within 2 minutes after reconnecting the hob to the grid
• Make sure all cooking zones are off.
• Do not press on.

1. Press the key and hold it down.
2. Each display shows a .
3. With one finger of the other hand press successively and quickly (in less than 2s) on the
   • Starting from the front right area and turning counter-clockwise (1 -> 2 -> 3 (only 42120) -> 4 -> 5) then release the key.
   • A double “beep” indicates an operating error. In this case, repeat the operation from step 1.
4. Select the [ C/0 ] key in display “4”.
5. Use the slider to make [ C/8 ] appear in display “4”.
6. Select the [ 0 ] key in display “5” and use the slider to enter the desired configuration in the display:

• Note: in this configuration, the right and middle zones are connected to the same phase.
• Press the key for 2 seconds to confirm the configuration.
• Never place the container on the cooking zones during setup.
• Novy NV reserves the right at any time and without reservation to change the structure and the prices of its products.
• NOVY nv
• Noordlaan 6
• B – 8520 KUURNE
• Tel. 056/36.51.00
• Fax 056/35.32.51
• E-mail:novy@novy.be
• http://www.novy.be
• United Kingdom: +44 (0)207 866 2493

Documents / Resources

| NOVY 42110 Hob Hood Novy Panorama 120 Pro [pdf] Instruction Manual
42110 Hob Hood Novy Panorama 120 Pro, 42110, Hob Hood Novy Panorama 120 Pro, Hood Novy Panorama 120 Pro, Novy Panorama 120 Pro, Panorama 120 Pro
---|---

References

• Innovatieve dampkappen en intuïtieve kookplaten - Novy

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>