STREETZ S250 Bluetooth Speaker Instruction Manual
- June 1, 2024
- STREETZ
Table of Contents
STREETZ S250 Bluetooth Speaker
Product Overview
- USB-C female (charge port, and LED indicator)
- MicroSD slot
- USB-A female for USB flash drive
- 3.5 mm audio female (“AUX”)
- Decrease volume/previous song
- Increase volume/next song
- Mode button
- Power button on/off/play/pause/answer/hang up
Charging
- Use the USB-C cable to connect to the speaker and to a USB adapter 5V, 1A (not included).
- The LED will change to red light, confirming it is charging. When it is fully charged the LED will turn off.
Use
- Press and hold the power button to turn the speaker on or off.
- Short press on the power button to play or pause.
- Increase volume: Short press on the “+” button.
- Decrease volume: Short press on the “- “ button.
- Previous song: Long press on the “-” button.
- Next song: Long press on the “+” button.
- Press the mode button to switch between Bluetooth, MicroSD and USB.
- If a USB flash drive or a MicroSD card is already inserted or just inserted, then music will play automatically.
- To use a MicroSD card or USB flash drive USB insert them into the corresponding slot.
- To use 3.5 mm audio connection. Connect a 3.5 mm cable to the speaker and to another device. Use the other device to control and play music.
- File type supported for music: MP3.
Bluetooth
-
Turn on the speaker. Bluetooth range is up to 10 meters.
-
Press the mode button to change to Bluetooth.
-
Use your phone or device to connect to the speaker. If needed see the manual of your device on how to use Bluetooth. If a pin code is requested, enter “0000”.
-
Use your phone or device to play and control the music.
While using Bluetooth the following buttons works from the speaker.- Previous song: Long press on the “-” button.
- Next song: Long press on the “+” button.
- Short press on the power button to play, pause, answer a call or to hang up.
Troubleshooting Bluetooth
Only one Bluetooth connection can be used at the same time.
If the connection fails, try forgetting the speaker from your device and try
to connect again. It might help to forget or remove other Bluetooth devices as
well.
TWS
2 speakers with the same article number are required for “TWS”. “TWS” is short
for “True wireless stereo”, it means that you can connect 2 identical speakers
wirelessly and play music from both in stereo, for a better music experience.
- If either or both speakers are connected to your phone or other device, then first turn off the Bluetooth on your phone or device.
- Turn on 2 speakers. Change them both to Bluetooth. A LED flashes, to confirm that the speaker is ready to pair.
- On one of the speakers, press and hold the mode button until a sound confirms. Wait a few seconds, now another sound should play and one of the speakers should have a flashing LED and the other should have a not flashing LED to confirm successful pairing.
- Use your phone or device to connect to the speaker. If needed see the manual of your device on how to use Bluetooth. If a pin code is requested, enter “0000”. A sound confirms successful connection.
- The speakers are now paired together and connected to your device. Try playing some music, you should hear music from both speakers now.
Disconnecting “TWS”
To disconnect, press and hold the mode button. They will disconnect from each
other.
Voice assistant
Press the mode button 2 times to activate the voice assistant function on your
phone or device.
Disposal of electric and electronic devices EC Directive 2012/19/EU This product is not to be treated as regular household waste but must be returned to a collection point for recycling electric and electronic devices. Further information is available from your municipality, your municipality’s waste disposal services, or the retailer where you purchased your product.
DistIT Services AB, Glasfibergatan 8, 125 45 Älvsjö, Sweden.
DistIT Services AB, Suite 89, 95 Mortimer Street, London, W1W 7GB, England.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>