Jungborn 10530163 Wall Mounted Toilet Instructions

June 12, 2024
Jungborn

Jungborn 10530163 Wall Mounted Toilet

Product Information

Product Name DUE 59
Article Number 10530163
Version 06/2023

Product Usage Instructions

Cleaning
For daily cleaning, use only commercial bath cleaners. Lime scale and soap residue can be removed with commercial lime remover or vinegar cleaners. Always follow the usage instructions provided by the manufacturers of the cleaning products.

Wall-Mounted Toilet Assembly
Refer to the respective language instructions for wall-mounted toilet assembly:

  • EN – Assembly Instructions Wall-Mounted Toilet
  • FR – Notice de montage WC suspendu
  • IT – Istruzioni di montaggio WC a parete
  • NL – Montagehandleiding hangtoilet

Safety Instructions
The instructions concerning persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, and children playing with the appliance are not applicable.

Cleaning and Water Drainage
Follow the steps below for cleaning and water drainage:

  1. Turn off the water supply.
  2. Disconnect the appliance from the mains.
  3. Loosen the drain plug by turning it anticlockwise.
  4. Remove the drain plug and empty the appliance.
  5. Never turn the unit over before draining, as it may permanently damage the electronics.

Replacing the Limescale Filter
To replace the limescale filter:

  • Refer to the respective language instructions for limescale filter replacement:
    • DE – Wechsel Kalkfilter
    • EN – Replacing the limescale filter
    • FR – Remplacement du filtre anticalcaire
    • IT – Sostituzione del filtro anticalcare
    • NL – Vervangen kalkfilter

Remote Control Usage
To use the remote control for the bidet:

  1. Sit on the bidet.
  2. Press the Rear spray or Front spray button on the remote control to start the cleansing process.
  3. The bidet will automatically stop cleansing after 3 minutes.
  4. You can also stop the cleansing process beforehand by pressing the Stop button.

Read the instructions carefully before use and keep them for future reference! For daily cleaning use only commercial bath clea ners. Lime scale and soap residue can be removed with commercial lime remover or vinegar cleaners.

ssembly Instructions Wall-Mounted Toilet

  • Electrical work and repairs may only be carried out by qualified electrici-ans.
  • The respective national installation regulations must be observed during installation.
  • The device must not be modified in any way. Electric shock and risk of accident.
  •  Always make sure that the power supply is disconnected before installa-tion.
  • If the power cord is damaged, it must be replaced by the manufacturer, its customer service or a similarly qualified person in order to avoid hazards.

The appliances must be earthed.

  • The instructions concerning persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge and children playing with the appliance are not applicable
  • Children being supervised not to play with the appliance.
  • Cleaning and user maintenance shall not be made by children without supervision.
  • The shower toilet set is used for comfortable cleaning and drying of the buttocks and vaginal area after using the toilet. Any other use automatically voids all liability and warranty claims.

Symbols used

Jungborn-10530163-Wall-Mounted-Toilet-fig-21

Cleaning

Before cleaning, always disconnect the unit from the power supply. Please use only commercially available cleaning agents and disinfectants and a soft damp cloth. Never use aggres-sive cleaners, scouring agents or products containing chlorine or solvents.

Water drainage

  • In case of transport or disassembly, you must empty the unit.
  • Turn off the water supply. Disconnect the appliance from the mains. Loo-sen the drain plug by turning it anticlockwise. Remove the drain plug and empty the appliance. Please never turn the unit over before you have drained it. You may permanently damage the electronics.

Jungborn-10530163-Wall-Mounted-Toilet-fig-2

Replacing the limescale filter

Jungborn-10530163-Wall-Mounted-Toilet-fig-3

The limescale filter is located in the supply line of the shower toilet and prevents the unit from becoming clogged with limescale deposits. The service life is 1/2 year on average, but this period is reduced if the water contains a lot of limescale. You can find out the respective degree of hardness from your public utility company. Replacement is necessary when the water pressure drops significantly. You can obtain further replacement filters from the dealer from whom you purchased the product.

Function overview

Jungborn-10530163-Wall-Mounted-Toilet-fig-4

Remote control Due 59

Jungborn-10530163-Wall-Mounted-Toilet-fig-5
Jungborn-10530163-Wall-Mounted-Toilet-fig-6

Batteries not included.

Rear spray / Front spray

Sit on the bidet. Press the “Rear spray” or “Front spray” button on the remote control; the bidet begins cleansing. Cleansing ends automatically after 3 minutes. You can also stop the cleansing process beforehand by pressing the “Stop” button.

Adjusting the nozzle position

Sit on the bidet. Start the “Rear spray” or “Front spray” programme. Press the “Nozzle position” button on the remote control and then the “Decrease” or “Increase” button to move the position of the nozzle forward or backward. The preset position is 5.

Adjusting the flow rate

Sit on the bidet. Start the “Rear spray” or “Front spray” programme. Press the “Adjusting the flow rate” button on the remote control and then the “Decrease” or “Increase” button to adjust the flow rate.

Adjusting the water temperature

Sit on the bidet. Start the “Rear spray” or “Front spray” programme. Repeatedly press the “Adjusting the water temperature” button on the remote control until the water tempera-ture symbol lights up. Then press the “Increase” or “Decrease” button to adjust the water temperature.

Pulse massage spray

Sit on the bidet. Start the “Rear spray” or “Front spray” programme. Then repeatedly press the “Massage” button on the remote control until you’ve reached your desired spray mode. The indicators on the remote control show the function.

  • Oscillating: 1 indicator lights up; Pulsating: 2 indicators light up;
  • Oscillating + Pulsating: 3 indicators light up

Setting the night light

The default night light mode is “Always on”. Start the „Water temperature“ programme. Then press the „-“ button of the nozzle position on the remote control repeatedly until you have selected your desired spray mode. “Close” mode: One indicator lights up; “Always on” mode: Two indicators light up; “Smart” mode: Three indicators light up.
PLEASE NOTE: In “Smart” mode, the night light turns on when its dark and turns off when it’s bright.

Self-cleaning the water tank

PLEASE NOTE: If the appliance has not been used for more than 72 hours and a user using the washing function, the self-cleaning function activates for 30 seconds. During self-clea-ning, all buttons are inactive and will be reactivated after self-cleaning.

Descaling

  • You need to descale the appliance at least once a year, or more often, depending on the number of cleaning cycles you’ve run and the quality of the water in your area. During de- scaling, you can continue to use the toilet, however, without the washing function. Descaling takes up to 30 minutes. During this time, the night light flashes continuously. When the night light stops flashing and the appliance emits a long beep, you can use the washing function again. Please use 150 ml of commercially available, non-foaming descaling agent.

  • Please note: Water flows out of the nozzle when the cover is opened. The appliance emits two beeps to indicate that you can now pour in the descaling agent.

Jungborn-10530163-Wall-Mounted-Toilet-fig-15

Removing the bidet seat

Jungborn-10530163-Wall-Mounted-Toilet-fig-16 Jungborn-10530163-Wall-Mounted-Toilet-fig-17

Replacing the bidet seat hinge

Jungborn-10530163-Wall-Mounted-Toilet-fig-18

Troubleshooting

Problem Potential cause Suggested action

The washing cyclus can not work

| 1.         The power supply may not be opened| Please turn on the power
2.         The water supply may not be opened| Please open the inlet water valve, or check if there is a water outage
3.         The filter may be blocked| Please replace a new filter .It has a service life of approx. half a year
4.         Maybe not in the seating state| Please sit on the seat and adjust sitting position
5.         Maybe the cover is closed| Please open the cover and sit on the toilet seat

6.         Maybe it is not used for more than 72 hours

| Not used for more than 72 hours ,when the user operates the washing ,it will open the self-cleaning for about 3 minutes. All the buttons are invalid during the self-cleaning and it will return to normal after the self-cleaning

The nozzle goes back suddenly

| 1.         The washing cycle is 3 mins. The nozzle will stop spraying after 3 mins, and then go back.| This is normal and please re-press the “wash” button to start washing again
2.         There may be some problems of water supply| Please check if there is a water outage
3.         Maybe the seated sensor detects the user left the seat| Please adjust sitting position
4.         Maybe the cover is closing| Do not put down the cover when it is washing

Low water flow rate

| 1.         The water flow rate may be set at low grades| Please increase the flow rate as per “adjusting water flow rate” of operating instructions
2.         The water supply pressure may be too low| Please check and ensure the water supply pressure is � 0.07 Mpa
3.         The filter may be blocked| Please replace a new filter .It has a service life of approx. half a year
4.         The nozzle may be blocked| Please replace a new nozzle

Low water tempera- ture

| 1.         The water temperature may be set at low grades| Please set the water temperature at high grade as per “adjusting temperature” of operating instruc- tions
2.         Maybe the temperature of water supply is too low| Please set the water temperature at high grade as per “adjusting temperature” of operating instruc- tions, or decrease the flow rate as per “adjusting water flow rate” of operating instructions.
The nozzle comes out slowly| When start washing function, the nozzle will be self-cleaning before coming out, and this will take some time| This is normal

The water flows out but

the nozzle do not come out

| 1.         When start washing function, the nozzle will be self- cleaning before coming out . This function

also takes place after the washing cycle.

|

This is normal

2.         Maybe it is not used for more than 72 hours| This is normal. Not used for more than 72 hours ,when the user operates the washing , it will open the self-cleaning for about 3 minutes

The dryer can not work

| 1.         The power supply may not be opened| Please turn on the power
2.         Maybe not in the seating state| Please sit on the seat and adjust sitting position
3.         Maybe the cover is closed| Please open the cover and sit on the seat

4.         Maybe it is not used for more than 72 hours

| Not used for more than 72 hours ,when the user operates the washing ,it will open the self-cleaning for about 3 minutes. All the buttons are invalid during the self-cleaning and it will return to normal after the self-cleaning

Low air tempera- ture

| 1.         The air temperature may be set at low grades| Please set the air temperature at high grade as per “adjusting temperature” of operating instructions
2.         The air heater can not work normally| Please contact local distributor

The remote con-

trol is not functioning

| 1.         Maybe there are not batteries in the remote control| Please install the correct batteries in the remote control
2.         Maybe the battery power is too low| When the battery power is too low the LED of grade will flash. Please replace the battery
3.         Maybe the code of the bidet and remote control is not the same| Set the remote control to the appropriate code (see page 27).
The bidet can not work normally| Maybe there is something abnormal| Please shut off the power and turn on after one minute. If the bidet still cannot work, please contact local distributor
There is constantly BEEP| The water supply temperature may be too high| Please shut off the power and water supply, stop using the product, and then contact local distributor

Nozzle cleaning

The nozzle is cleaned before and after washing. Open the lid and the seat, but do not sit on the bidet. Press and hold the “Set temperature” button on the remote control and then press the “–” button. The nozzle then extends with cleaning water. It returns automatically after 5 minutes, or you can press the “Stop” button.

Jungborn-10530163-Wall-Mounted-Toilet-fig-19

Remote control teach-in

If you install several electronic bidets in the same area and you want each remote control to control the specified electronic bidet, please follow the steps below. The same procedure applies to teaching a new remote control.

  1. Close the cover and the seat.
  2. Press and hold the stop button and one of the temperature setting buttons („+“ or „-“) on the remote control simultaneously for a few seconds. You will then hear the appliance „beep“ and in the meantime the indicator light of the first level will light up.
  3. Release the „Stop“ button but still hold down the temperature setting selection button.
  4. Press the „-“ and „+“ buttons of the flow in succession and then release the selector button of the temperature setting. At this point, the display with the current ID code of the product lights up and the light of the fifth stage flashes permanently.
  5. By pressing the „-, +“ buttons of the flow, you can change different product ID codes and the corresponding indicator will light up. There are 32 ID codes in total. By default, the first code is set and the first stage lights up.
  6. Open the lid and close it again immediately. Then press the „Stop“ button on the remote control before the indicator goes out. (After the ID selection is completed, the indicator light remains lit for 20 seconds).

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals