LNC HA0519301 Aeyilana 5 Light Brass Kitchen Island Light Instruction Manual

June 1, 2024
LNC

LNC HA0519301 Aeyilana 5 Light Brass Kitchen Island Light

Product Information

Specifications:

  • Item Number : A0519301
  • Voltage : 120V
  • Maximum Wattage : LED, 30W

Product Usage Instructions

Tools Required:

  • Ladder
  • Philips Head or Flat Blade Screwdriver
  • Electrical Tape
  • Pliers
  • Wire Cutter/Stripper

Parts Included:

  • (E) Canopy screw (4)
  • (F) Mounting plate (1)
  • (G) Canopy (1)
  • (H) Lock nut (5)
  • (I) Cable (5)
  • (J) Pipe (5)
  • (K) Lampshade (5)

Assembly & Installation Instructions:

  1. Remove the fixture from the carton and ensure all parts and accessories are included.
  2. Turn off the power supply before starting the installation.
  3. Attach mounting plate (F) to the wall using screws (B & C).
  4. Mark the hole positions on the wall using a pen.
  5. Drill holes and insert anchors (A) until they are level with the wall.
  6. Secure mounting plate (F) to the wall using anchor screws (B) and mounting screws (C).
  7. Connect wires following the provided charts. Do not connect other wires to ground wires.

Additional Safety Tips:

  • Ensure the mounting surface is clean, dry, and strong enough to support the canopy.
  • Avoid placing the lamp near acidic or alkaline substances.
  • When replacing bulbs, wait for the lamp to cool down before proceeding.

FAQ:

  • Q: Can I use a higher-wattage bulb than recommended?
    • A : It is not recommended to exceed the maximum wattage of LED, 30W as it may cause damage to the product.
  • Q: Do I need a licensed electrician for installation?
    • A : While it is suggested to have a licensed electrician install the product, you can follow the provided instructions carefully if you have experience with electrical work.

WARNING (To reduce the risk of fire, electric shock, or personal injury):

  1. We suggest installation by a licensed electrician.
  2. Please read the instructions carefully and save it as you may need it at a later time.
  3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
    • » Go to the main fuse, or circuit breaker, box in your home.
    • Place the main power switch in the “OFF” position.
    • » Place the wall switch in the “OFF” position.
  4. The mounting surface should be clean, dry, flat, strong enough, and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
  5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
  6. Make sure the voltage you are using is 120V. The maximum wattage is LED, 30W.
  7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
  8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
  9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution, and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

LNC-HA0519301-Aeyilana-5-Light-Brass-Kitchen-Island-Light-
FIG3

**TOOLS REQUIRED

**

Before starting assembly and installation please prepare the needed tools as below picture

LNC-HA0519301-Aeyilana-5-Light-Brass-Kitchen-Island-Light-
FIG2

PARTS TYPE & QTY INCLUDED:

  • (E) Canopy screw (4)
  • (F) Mounting plate (1)
  • (G) Canopy (1)
  • (H) Lock nut (5)
  • (I) Cable (5)
  • (J) Pipe (5)
  • (K) Lampshade (5)

ACCESSORIES & QTY ENCLOSED:

  • (A) Anchor (4)
  • (B) Anchor screw (4)
  • (C) Mounting screw (2)
  • (D) Plastic Wire Connector (3)

LNC-HA0519301-Aeyilana-5-Light-Brass-Kitchen-Island-Light-
FIG3

ASSEMBLY & INSTALLATION INSTRUCTIONS

  1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
  2. Turn off power

Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

» Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
» Place the wall switch in the “OFF” position.

Make installation

LNC-HA0519301-Aeyilana-5-Light-Brass-Kitchen-Island-Light-
FIG4

Step A1 » 1 ) Unscrew canopy screws (E) from canopy (G).

2) Gently remove mounting plate (F) and then set them aside for later installation. Step A2 » Carefully pass the supply wires from the outlet box through mounting plate (F).

  1. NOTE :To drill the holes in the wall for anchors (A), attach mounting plate (F) to wall with screws (B&C)
  2. Attach mounting plate (F) to outlet box and then mark the position of holes in the wall with a pen as shown in the illustration.
  3. Drill holes and gently knock anchors (A) into the marked holes until anchors (A) are level with the wall.
  4. Secure mounting plate (F) to the wall with screwing anchor screws (B) into anchors (A) and mounting screws (C) into holes of mounting plate (F).

Step A3 » Make wire connections

Connect wires as shown in the charts below. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

Connect ground wires according to the chart below

LNC-HA0519301-Aeyilana-5-Light-Brass-Kitchen-Island-Light-
FIG5

Connect ground wires according to the chart below Connect wires according to the chart below

LNC-HA0519301-Aeyilana-5-Light-Brass-Kitchen-Island-Light-
FIG6

Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box

Step A4 »

1) Unscrew canopy screws (E) from the canopy (G).
2) Gently remove the mounting plate (F) and then set it aside for later installation. Carefully pass the supply wires from the outlet box through the mounting plate (F).

  1. NOTE :To drill the holes in the wall for anchors (A), attach a mounting plate (F) to wall with screws ( B & C )
  2. Attach mounting plate (F) to the outlet box and then mark the position of holes in the wall with a pen as shown in the illustration.
  3. Drill holes and gently knock anchors (A) into the marked holes until anchors (A) are level with the wall.
  4. Secure mounting plate (F) to the wall with screwing anchor screws (B) into anchors (A) and mounting screws (C) into holes of mounting plate (F).
    • 1) Position canopy (G) in place.
    • 2) Carefully thread canopy screws (E) through the holes in the canopy (G) and mounting plate (F) and then secure them by tightening canopy screws (E).
    • Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
    • Step A5 » 1) Screw pipes (J) onto top of lampshades (K).
    • 2) Please adjust the hanging height of the fixture :
  • Press down and hold the lock nuts (H) of the canopy by hand.
  • Pull or push steel cables (I) in and out of canopies to increase or decrease the hanging height.

.Check that everything is installed properly, then you can turn on the light. We hope you enjoy your new lighting!

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

CLEANING

To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

LNC User Manuals

Related Manuals