Minka Lavery 6702-66 Shimmering Elegance Wall Sconce Installation Guide

Minka Lavery 6702-66 Shimmering Elegance Wall Sconce

Product Information

Specifications:

• Model: 6702-66
• Release Date: New. 2023/12/7
• Maximum Wattage: 60 watts per candelabra base bulb or CFL/LED equivalent
• Mounting Screw  Size: #8-32N*L1
• Includes: Mounting Plate, Ground Screw, Mounting Screws (2)

Product Usage Instructions

1. Mounting the Fixture:
2. Shut off power at the fuse box or circuit breaker.
3. Remove the old fixture and mounting hardware.
4. Attach mounting plate (A) to outlet box using mounting screws (B).
5. Connecting the Wires:
6. Connect electrical wires as shown in Fig. 2.
7. If there is a ground wire in the outlet box, connect the fixture’s ground wire to it. Otherwise, connect directly to the mounting plate using the green screw.
8. Tuck wire connections neatly into the outlet box.
9. Finishing the Installation:
10. Place fixture body (D) over the mounting plate and secure with screws (C).
11. Install candelabra base bulbs or CFL/LED equivalent up to the maximum wattage allowed.
12. Hook stone and crystal strings to the respective tier rings of the fixture cyclically.

FAQ (Frequently Asked Questions)

1. Q: Can I use bulbs with wattage higher than 60 watts?
   A: No, do not exceed the maximum wattage rating to ensure safety and proper functioning of the fixture.

2. Q: What should I do if my outlet box does not have a ground wire?
   A: In such cases, connect the fixture’s ground wire directly to the mounting plate using the green screw provided.

3. Q: Is the fixture installation reversible?
   A: Yes, you can remove the fixture by reversing the installation steps and disconnecting the wires carefully.

INSTALLATION INSTRUCTIONS

Item#6702-66 (New. 2023/12/7)
READ AND SAVE THESE INSTRUCTIONS
WARNING ! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER ..

MOUNTING THE FIXTURE (Fig.1)

1. Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts in a clear area. Take care not to misplace any small parts necessary for installation.

3.  Attach mounting plate (A) using mounting screws
   (B) (Size: #8-32N*L1”) to outlet box (Not included). The side of the mounting plate marked “GND” must face out.
   CONNECTING THE WIRES (Fig. 2)

4. Connect electrical wires as shown in Fig. 2, making sure that all wire connectors are secured. If your outlet box has a ground wire (green or bare copper), connect fixture’s ground wire to it. Otherwise, connect fixture’s ground wire directly to mounting plate using green screw provided.

5. Tuck wire connections neatly into the outlet box.
   FINISHING THE INSTALLATION (Fig.1)

6. Place fixture body (D) over mounting plate (A), and secure with screws (C).

7. Install (2) two candelabra base bulbs up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification—DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)

8. Hook stone strings (A2) and crystal beads (B2) to first tier and second tier ring of fixture (D) cyclically.

9. Hook crystal strings (C2) and stone strings (D2) to third tier ring of fixture (D) cyclically.

10. Hook crystal strings (E2) and stone strings (F2) to fourth tier ring of fixture (D) cyclically.
    Your installation is now complete. Return power to the outlet box and test the fixture.

Note: Illustration (Fig.1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.
Min 75℃ supply conductors.
6702-66A

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>