MINKA LAVERY 5285-788 Atella 12 Inch W 5-Light Ashen Gold Led Incandescent Wall Sconce Instruction Manual

MINKA LAVERY 5285-788 Atella 12 Inch W 5-Light Ashen Gold Led

Incandescent Wall Sconce

Product Information

Specifications

• Item Number: 5285-788
• Maximum Wattage: 60 watts per bulb
• Base Type: E12
• Fixture Compatibility: CFL or LED bulbs

Product Usage Instructions

Preparation

1. Shut off power at the fuse box or circuit breaker and remove the old fixture along with the mounting hardware.
2. Unpack the new fixture carefully and lay out all parts in a clean area, ensuring not to misplace any small parts necessary for installation.

Mounting the Fixture

1. Remove mounting plate (A) from backplate (C) by unscrewing screws (D) located on the side of the backplate (C).
2. Attach mounting plate (A) to the junction box (JB) using provided screws or screws from the previously installed mounting strap. Ensure the plate is plumb and secure it by tightening the screws.

Connecting the Wires

1. Connect the electrical wires as shown in Fig.2, ensuring all wire connectors are secured. Connect the fixture’s ground wire to the junction box’s ground wire or directly to the mounting plate using the green screw provided.
2. Tuck wire connections neatly into the junction box.

Finishing the Fixture

1. Mount the fixture to the wall by aligning the backplate (C) with the mounting plate (A) and securing them together with screws (D).
2. Install the crystal bobeche (cb) over the candle sleeve (cs) and repeat for all crystals. Install light bulbs according to specifications.
3. Do not exceed the maximum wattage rating specified for the fixture.
4. Turn the power on and test the fixture once the installation is complete.

Frequently Asked Questions

• Q: Can I use bulbs exceeding 60 watts with this fixture?
  • A: No, it is not recommended to exceed the maximum wattage rating of 60 watts per bulb for this fixture.
• Q: How should I position the mounting plate during installation?
  • A: Ensure that the side of the mounting plate with “GND” marked on it and two convex points faces outward. Use a level to ensure the plate is plumb during installation.

Installation Instruction

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.

PREPARATION (Fig.1)

1. Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation.
   MOUNTING THE FIXTURE

3. To begin, it will be necessary to remove mounting plate (A) from the back plate (C) by removing screws (D) located on the side of the back plate (C). see fig. 1.

4. To begin the installation, first attach a mounting plate (A) to the junction box (JB) “not provided” by using 8-32 screws (B) or the screws from the previously installed mounting strap or plate. Make sure threaded holes are on the top and bottom when installing the mounting plate and the plate is plumb when by placing a level across the side. Adjust plate and tighten screws to secure the mounting plate.The side of mounting plate (A) with “GND” marked on it and two convex points must face out.
   CONNECTING THE WIRES (Fig. 2)

5. Connect the electrical wire as shown in Fig. 2, making sure that all the wire connectors are secured. If your junction box has a ground wire (green, or bare copper), connect the fixtures ground wire to it. Otherwise, connect the fixture ground wire directly to the mounting plate (A) using green screw provided.

6. Tuck wire connections neatly into the junction box (JB).
   FINISHING THE FIXTURE

7. To mount the fixture to the wall. Slip back plate (C) over the mounting plate (A) and align holes at top and bottom of backplate (C) with threaded holes on top and bottom of mounting plate (A).

8. Thread in screws (D) removed earlier to secure back plate (C) to mounting plate (A).

9. To begin installing the accessories, take the crystal bobeche (cb) and slip it down over the candle sleeve (cs). Repeat the process until all crystals are fully installed.

10. Install 5x E12 base light bulbs (LB) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification.

DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)

Your installation is now complete. You can now turn the power ON and test the fixture.

Note: The illustration (Fig. 1) in this manual is for installation purposes only. It may or may not be identical to the fixture purchased

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>