Micron PT102V Mobile Emergency Response System User Manual

June 1, 2024
Micron

PT102V Mobile Emergency Response System
User Manual

Document Title|
---|---
Version| 1
Finale Date| 22-04-08
Status| Released
Document Control ID|

 Introduction

PT102V is a rescue device with voice function.It works on LTE B4 / B13 network with superior receiving sensitivity. Based on the embedded wireless tracking protocol, PT102V can communicate with the backend server through LTE network, and transfer emergency reports.

 Product Overview

2.1 AppearanceMicron PT102V Mobile Emergency Response
System Figure1-1
2.2 Buttons Description
Button/12 PIN Interface Description

KEY/interface Description
TES TKey Query How much energy left.
SOS KEY Press this key to dial a phone number through LTE network
Reset Key Press this key to shut down the device in a bnormal condition

2.3 LED Description To be added Figure 1-2 There are 2LED lights in PT102V device, the description as following.

Light Event State
Red LED Power on Steady light
charging Slow flash
Blue LED Power on Steady light
Network indicate Slow flash

Getting Started

3.1 Parts List

Name Picture Remark
Rescue device
charging Dock

3.2 Battery Charging
The following items are suggestion for battery charge, please pay more attention.
The red LED of charging Dock will be steady light no matter rescue device is charging or not.
Charging will last about 3 hours.
Note: If the Rescue device is firstly used, please make sure the battery is fully charged, which will make the life of battery much longer.
3.3 Charging Dock
Charging Dock is a base with an AC Adapter.
The charging dock is used for device charging , which can be used for charging at any time ( by end user)..Micron PT102V Mobile Emergency Response System -
charging Dock 1 3.4 Poweron/ Power off

Power on:
Press the SOS key at least 3 seconds and release it to power on rescue device.
Power off:
Rescue device is auto power off and user can’t turn off the machine by itself.

Frequency

LTE:B4/ B13
WIFI:2.4GHz (only support receive function)
433: 433.92MHz (only support receive function)
GPS: 1575.42MHz (only support receive function)

Trouble shooting and Safety info

5.1 Trouble shooting

Trouble Possible Reason Solution

Messages can’t be reported to the
backend server by Mobile network.| APN is wrong. Some APN can not visit the internet directly.| Ask the network operator for the right APN.
The IP address or port of the backend server is wrong.| Make sure the IP address for the
backend server is an identified address in the internet.
Unable to power off ATW.| The function of power key was disabled by AT+GTFKS.| Enable the function of power key by AT+GTFKS.
Battery can not be charged| The battery has not been used for too long time and has been locked.| Using a external power source with 3.6V to 4.2V DC power supply to active the battery or apply for after sale help.
ATW can’t fix GPS successfully.| The GPS signal is weak.| Please move ATW to a place with open sky.
It is better to let the top surface face to the sky. (The same surface with indication LED)

5.2 Safety info

The following items are suggestion for safety use, please pay more attention.
Please do not disassemble the device by yourself.
Please do not put the device on the overheating or too humid place, avoid exposure to direct sunlight. Too high temperature will damage the device or even cause the battery explosion.
Please do not use the device on the airplane or near medical equipment.
FCC Caution.
§ 15.19 Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
15.21 Information to user.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
15.105 Information to the user.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuming the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the eceiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
IRF Exposure Information (SAR) :
This device is also designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA) and ISED(Canada) The SAR limit of FCC/ISED is 1.6 Wékg averaged over one gram of tissue.
Device types: PT102V (FCC ID: ZKQ-PT102V)(IC: 8414B-PT102V) has also been tested against this SAR limit.
uring the product certification period, according to this standard report test, the ighest SAR value reported to the FCC/ISED when the device is in use It is 1.27Wkg. This device was tested for typical body-wom operations with the edge of the device kept 5mm from the body. To maintain compliance with FCC/ISED RF exposure requirements, use accessories that maintain a 5mm separation distance between the user’s body and the edge of the device.
ISED RSS Warning:
This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals