Micron Bolt-2 Powerful GPS Locator

User Manual
Revision: 1.00

Bolt-2 Powerful GPS Locator

Document Title|
---|---
Version| 1
Finale Date| 23-04-21
Status| Released
Document Control ID|

Introduction

Bolt-2 is a powerful GPS locator designed specifically for monitoring and tracking the position of items such as cars. Its location can be real time or schedule tracked by backend server or specified terminals. Based on the embedded wireless tracking protocol, Bolt-2 can communicate with the backend server through 4G LTE Cat M network, and transfer reports of emergency, Geo- fencing, device status and scheduled GPS position etc…Service provider is easy to setup their tracking platform based on the functional wireless tracking protocol. The WIFI function will be activated and report the MAC addresses once the device is in alerting state.

Product Overview

Appearance

Figure 2 – 1

LED Description

Getting Started

Parts List

1](https://manuals.plus/wp-content/uploads/2023/07/Micron-Bolt-2-Powerful-GPS- Locator-Getting-Started-1.jpg)| The LTE/GPS locator.

Insert SIM Card

RF433

According to the configuration, Bolt-2 can send a message every 35 seconds. When the receiver enters the RF433 sending distance of Bolt-2, it can receive a signal, and the closer the distance, the stronger the signal, thus determining the location range of Bolt-2.

Power on/Power off

It will automatically turn on when charging and turn off when the battery is depleted

REMOVE

The removal detection button of Bolt-2 is in a pressed state for a long time due to sticking to an object during normal operation. When Bolt-2 is moved, the button pops up and a prompt will be sent to the user

Frequency

LTE:Band2 Band4 Band12 Band13

WIFI:2.4GHz(WIFI is only used for scanning)
GPS:1575.42MHz

Trouble shooting and Safety info

Trouble shooting

Messages can’ t be Reported to the
backend server by Mobile network.| APN is wrong. Some APN can not visit the Internet directly.| Ask the network operator for the right APN.
The IP address or port of the backend server is wrong.| Make sure the IP address for the backend server is an identified address in the internet.
Unable to power off AT-NG5.| The function of power key was disabled by
AT+GTFKS.| Enable the function of power key by AT+GTFKS.
Battery can not be charged| The battery has not been used for too long time and has been locked.| Using a external power source with 7.2V to 8.4V DC power supply to active the battery or apply for after sale help.
ATW can’ t fix GPS successfully.| The GPS signal is weak.| Please move ATW to a place with open sky.
It is better to let the top surface face to the sky. (The same surface with indication LED)

Safety info

The following items are suggestion for safety use, please pay more attention.

• Please do not disassemble the device by yourself.
• Please do not put the device on the overheating or too humid place, avoid exposure to direct sunlight. Too high temperature will damage the device or even cause the battery explosion.
• Please do not use the device on the airplane or near medical equipment.

FCC Caution.
§ 15.19 Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

§ 15.21 Information to user.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’ s authority to operate the equipment.

§ 15.105 Information to the user.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

WIFI Exposure Information:
WIFI of this equipment only has reception function.

BT Exposure Information:
BT of this equipment only has reception function.

RF Exposure Information :
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body .

ISED RSS Warning:
This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: ( 1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

WIFI Exposure Information:
WIFI of this equipment only has reception function.

Radiation Exposure Statement :
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

The following warning statements
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Exposure to Radio Frequency Radiation. This equipment must be installed and operated in accordance with provided instructions, and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter.

This device complies with Industry Canada RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

• This Class B digital apparatus complies with Canadian ICES-003.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>