RHINO-RACK RSIT Stow It Utility Holder Instructions
- June 13, 2024
- RHINO RACK
Table of Contents
RHINO-RACK RSIT Stow It Utility Holder
Product Information
The Stow-It – RSIT is a product designed by Rhino-Rack Australia Pty. Ltd. It is a versatile accessory for carrying loads on your vehicle. The product has a carrying capacity of up to 8kg/18lbs, which should be evenly spaced between the two carriers. The clamping width of the carriers is 10-50mm. The product comes withvarious parts including Stow-it assembly, M6 x 16mm socket head screws, M6 x 20mm socket head screws, M6 x 16mm flat washers, M6 channel nuts, a 5mm allen key, and metal keys.
Product Usage Instructions
- Before starting the installation process, it is important to check the Rhino-Rack website to ensure you have the latest issue of the instructions.
- Refer to your fitting instruction to ensure that the Stow-It accessory is installed correctly.
- Check the contents of the kit before starting the fitment and report any discrepancies.
- After completing the installation, place these instructions in the vehicle’s glove box.
- It is essential to follow these instructions for the warranty to be upheld.
Fit Time:
Approximately 10 minutes
Torque Settings:
Unless stated otherwise in these instructions, all fasteners should be set
to the following torque settings:
- M6 : 4-5Nm (3-4lbs/ft)
Note: All bolted connections should be checked each time they are re- fitted, especially during service maintenance checks.
Important Note for Dealers and Fitters:
It is your responsibility to ensure that these fitting instructions are
given to the end-user or client. These instructions remain the property of
Rhino-Rack Australia Pty. Ltd. and may not be used or changed for any other
purpose than intended.
Stow-It RSIT
Important:
- Check the Rhino-Rack website to ensure you have the latest issue of these instructions.
- Please refer to your fitting instructions to ensure that the accessory is installed in correctly.
- Check the contents of the kit before commencing fitment and report any discrepancies.
- Place these instructions in the vehicle’s glove box after installation is complete.
- These instructions must be followed for the warranty to be upheld.
Fit Time: 10 min
Instructions
Carrying Capacity
Max system load capacity
The max load permissible is 8kg/18lbs evenly spaced between the two carriers.
Diameter clamping width, 10-50mm.
Torque Settings
Unless stated otherwise in these instructions, all fasteners should be set to
the following torque settings
- M6 : 4-5Nm (3-4lbs/ft).
Warning
- Do not attempt to fit the accessory to your vehicle unless you fully understand these fitting instructions. Please direct any questions regarding fitting to the dealer from where the product was purchased.
- Although the accessory is tested and approved to AS1235-2000 / ISO 11154, off-road conditions can be much more rigorous.
- Extreme care must be taken in off-road conditions.
- The accessory must be removed when the vehicle is put through an automatic car wash.
- Always ensure you fasten your load securely.
- Ensure the product is locked before driving.
In-service maintenance checks
- All bolted connections should be checked after driving a short distance when you first install your roof racks & accessories.
- All bolted connections should be checked again at regular intervals ( every 1000k (621mi) is recommended, depending on road conditions, usage, loads and distances travelled). All bolted connections should be checked each time they are re-fitted.
Note for Dealers and Fitters
It is your responsibility to ensure these fitting instructions are given to
the end-user or client. These instructions remain the property of Rhino-Rack
Australia Pty. Ltd. and may not be used or changed for any other purpose than
intended.
Parts List
| Item | Description | Qty |
|---|---|---|
| A | Stow-it assembly. | 2 |
| B | M6 x 16mm socket head screw | 2 |
| C | M6 x 20mm socket head screw | 2 |
| D | M6 x 16mm flat washer | 2 |
| E | M6 channel nut | 2 |
| F | 5mm Allen key | 1 |
| G | Metal key | 2 |
ASSEMBLY INSTRUCTIONS
NOTE:
Key Removal RSIT Shovel Holder
Tools required:
T1 – Allen key (provided in RSIT kit).
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>