Micron Electronics AT NG Tracker User Manual

June 6, 2024
Micron Electronics

**Micron Electronics AT NG Tracker User Manual

**

Introduction

AT NG use lithium battery. it is a powerful GPS locator which is designed for vehicle, and assets tracking . With superior receiving sensitivity, Its location can be real time or schedule tracked by backend server or specified terminals. Based on the embedded wireless tracking protocol, AT NG can communicate with the backend server through LTE Cat-M network, and transfer reports of emergency, Geo-fencing, device status and scheduled GPS position etc…
Service provider is easy to setup their tracking platform based on the functional wireless tracking protocol.

The WIFI function will be activated and report the MAC addresses once the device is in alerting state.

Product Overview

Appearance

Appearance
Appearance Appearance
Appearance

LED Description

There is one tricolor LED lights in AT NG device, the description as following.
LED Description

Light

| Event|

State

---|---|---

LED show blue

| GPS fixed| Solid
LED show red| low power|

Solid

Getting Started

Parts List

Name

| Picture| Remark
---|---|---
AT NG| LED Description|

The LTE/GPS locator.

How GPS position Fix

Your device has an unobstructed view of the sky, lying face up, so it can obtain the initial GPS Fix.
How GPS position Fix

Insert SIM Card

Insert SIM Card

Device Power on

Long press the power button for 4 seconds, and the device will start when the red and blue light lights up.
Device Power on

Trouble shooting and Safety info

Trouble shooting

Trouble

| Possible Reason|

Solution

---|---|---

Messages can’t be reported to the backend server by Mobile network.

| APN is wrong. Some APN can not visit the internet directly.| Ask the network operator for the right APN.
The IP address or port of the backend server is wrong.|

Make sure the IP address for the backend server is an identified address in the internet.

Unable to power off AT NG.

| The function of power key was disabled by AT+GTFKS.| Enable the function of power key by AT+GTFKS.
Battery can not be charged| The battery has not been used for too long time and has been locked.|

Using a external power source with

3.65V DC power supply to active the battery or apply for after sale help.

AT NG can’t fix GPS successfully.

| The GPS signal is weak.| Please move AT NG to a place with open sky.

It is better to let the top surface face to the sky. (The same surface with indication LED)

Safety info

The following items are suggestion for safety use, please pay more attention.

  • Please do not disassemble the device by yourself.
  • Please do not put the device on the overheating or too humid place, avoid exposure to direct sunlight. Too high temperature will damage the device or even cause the battery explosion.
  • Please do not use AT NG on the airplane or near medical equipment

FCC Caution

§ 15.19 Labelling requirements

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

§ 15.21 Information to user.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

§ 15.105 Information to the user.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

IC Caution:

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions:

  1. this device may not cause interference,
  2. this device must accept any interference, including interference that may cause undesired operation of the device.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals