Carry-on 1000nit 21.5 Inch Carry On Broadcast Monitor User Manual
- September 26, 2024
- Carry-on
Table of Contents
1000nit 21.5 Inch Carry On Broadcast Monitor
“`html
Specifications
-
Screen Size: 21.5 inches
-
Brightness: 1000nit
-
Resolution: Full HD
-
Input: 4K@60 HDMI, 3G-SDI, DVI, Tally Signal
-
Output: HDMI, 3G-SDI
-
Features: HDR Monitoring, Custom 3D-LUT, Waveform, Histogram,
Focus Assist, Monochrome -
Power Supply: DC IN, XLR, V-mount battery plate
Product Usage Instructions
1. Power Supply
There are three ways to power the monitor:
-
Use the direct plug-in power input port with the correct
polarity. -
Connect via the 4-pin XLR interface with the correct
polarity. -
Add a compatible battery to the battery plate.
2. Portable Protective Case
1.1 Rotate the butterfly lock: To disassemble
the front or rear cover easily.
1.2 Screw Threads: The top, left, and right
sides have 1/4 and 3/8 screw threads for mounting additional
devices.
1.3 Hidden Stand: The bottom of the case has a
built-in stand for enhanced stability on flat surfaces.
3. Panel Instructions
3.1 Front Panel
The front panel features intuitive buttons for easy operation
and access to custom function shortcut buttons.
3.2 Rear Panel
-
Tally Indicator: Red, Green, Yellow
-
Handle
-
V-mount Battery Plate
-
Inputs and Outputs: 23G-SDI, 2HDMI, 1*DVI (VGA input after
conversion) -
Tally Signal Input
-
LUT File/Upgrade File Port
-
VESA Holes: 100x100mm
Frequently Asked Questions (FAQ)
Q: Can I use any battery with the monitor?
A: The monitor comes with a default Sony V-Mount Plate. However,
you can choose different battery plates according to your
needs.
Q: How can I clean the monitor?
A: Use a clean soft cloth to wipe the monitor. Avoid using
chemical solutions to clean the product.
Q: Can I disassemble or repair the unit myself?
A: To avoid damaging the product, do not take it apart or repair
it yourself unless you have adjustable components in the unit.
“`
21.5″ Carry-on Broadcast Monitor High Brightness 1000nit
User Manual
Foreword
Thank you for purchasing our high bright carry-on broadcast monitor. Please
read this manual carefully before using the unit. Have a great experience!
Caution
1. Please use the adapter in the accessory, and use the qualified battery if
need.
2. Please do NOT expose this product directly in the sunlight, heat, and
humid conditions.
3. Please keeps the monitor away from the strong light while using this
product to ensure the image effect and long-term use.
4. Please avoid heavy impact or drop onto the ground. 5. Please do NOT use
chemical solutions to clean this product.
Please wipe the monitor with a clean soft cloth to maintain the brightness of
the surface. 6. To avoid damaging the product, please do not take apart or
repair the unit by yourself without adjustable component in the unit.
Product Feature
Full HD panel, viewing details with confidence High bright 1000nit, visible in
sunlight Portable protective case, easy to handle various tasks Intuitive
buttons operation, 4 custom function shortcut buttons to
improve work efficient
1
Support 4K@60 HDMI Input and Output Under HDMI signal the audio meter level
can be display max 8
channels; under SDI signal can be display max.16 channels HDR monitoring, what
you see is what you get Custom 3D-LUT, preview film look With Waveform,
Histogram, Focus Assist, Monochrome etc.
functions, help you accurately exposure and focus every shot Dual speakers
Built-in front and rear Tally light, enhance team cooperation Multiple power
supply ways (DC IN, XLR , V-mount battery plate)
2
CONTENTS
1. Portable Protective Case ————————————- 4 2. Product Description
——————————————– 5 2.1 Front Panel ——————————————————– 5 2.2 Rear Panel
——————————————————— 7 2.3 Power Input Way ————————————————- 8 2.4 TALLY
Indicator Connection ———————————- 9 3. Menu Operation Instruction ———————————-
8 4. Menu Function Instruction ———————————– 10 5. How to Import LUT
———————————————- 10 6. Support Signal Formats ————————————— 17 7. Parameters
——————————————————— 18 8. Trouble Shooting ———————————————— 18
3
1. Portable Protective Case
1.1. Rotate the butterfly lock to easy disassembly the front or rear cover
Butterfly lock
1.2. The top, left and right side of the protective case are with 1/4, 3/8
screw thread can be extend to mount wireless transmission or other device
4
1.3. The bottom of case built-in hidden stand support up to 30cm, ensure
enhanced stability on any flat surface such as desks, floors,and other areas,
allowing for a secure standing position.
2. Panel Instruction
2.1 Front Panel
5
Number
Instruction Speaker 3.5mm headphone jack Mute Key When the menu is not displayed, press it to turn on mute. When turned on, the button will display a green constant light; closed the mute function , the button light turn off Signal Input Selection When the menu is not displayed, the signal input source can be selected. After selection, the button will display a green constant light. Custom Function Key Users can enter the main menu User Option Shortcut Key to set F1~F4 as common function keys. After setting and close menu, simply press to turn on or off the function Return/Exit menu Function when OSD is displayed Rotate to select the desired function or parameter, and press confirm after selection Function when OSD is not displayed Rotate to adjust volume or backlight (can be set to volume or backlight in the menu User Option Left Right Key Set) Press to enter main menu Power Indicator After the monitor is properly connected to the power, turn on power switch the indicator display red, and display green after input signal Power ON/OFF Tally IndicatorRedGreenYellow
6
1.2 Rear Panel
Number
Instruction Tally IndicatorRedGreenYellow Handle V-mount Battery Plate 23G-
SDI Signal Inputs and Outputs 2HDMI Signal Inputs1*HDMI Signal Output DVI
Signal Input (VGA input from this port after conversion module signal
conversion) Tally (Indicator) Signal Input
7
LUT File/Upgrade File Importing port
The direct DC plug-in power input port supply
4-pin XLR DC power input
VESA Holes 100x100mm
2.3 Power Input Way
There are three ways of power supply to our monitor:
a. Powered by the direct plug-in power input port supply.
Please select DC power plug supply and the polarity is as image below:
b. Via 4 pin XLR interface power supply, to share power with
the camera or via power adapter input.
Polarity of the 4-pin XLR power input as below image, please note the polarity
of the power input, otherwise it may damage monitor.
c. Add battery to the monitor battery plate to supply the power.
The product back case including battery plate is available for two types of
batteries. Customers can choose different battery plates according to their
needs. (If the customers have no requirement on the battery, the factory
assembles Sony V-Mount Plate by default).
Battery Plates
8
Panasonic Anton Plate Sony V-Mount Plate
We assemble the suitable battery plate for the customers according to the
different requirements of the batteries. If the customers have no requirement
on the battery, the factory assembles Sony V-Mount Plate by default.
Remark: According to the different specification of the battery, the
capability is different, and the working time for the monitor will be
different. Higher capability (working time) will be longer.
Without the charging circuit design for the monitor, please remove the battery
to charge with the battery charger.
Suggestion: Better to remove the battery if don’t use this product in a long
time.
2.4 TALLY Indicator Connection
Indicator colors Pin connection
Green
1-5
Red
6-5
Yellow
9-5
9
3. Menu Operation Instruction
After the monitor is properly connected to the power, turn on the monitor
power switch. 3.1 Press MENU knob to enter OSD main menu, and rotate it to
select the first
level menu, the icon will turn gray after selected, press MENU knob confirm to
enter the secondary menu. 3.2 After enter the secondary menu, rotate MENU knob
to select the function, and press it confirm to enter three level menu, then
rotate MENU knob to select turn on/off the function or select the detail
parameter, press MENU knob confirm after selected 3.3 Press EXIT button to
exit the menu
4. Menu Function Instruction
Assist
ON, OFF After turning on, waveform, vector, histogram and embedded
10
All Waves Waveform Vector scope Histogram
Focus Assist
audio will be shown.
ON, OFF Mode: RGB, YUV, Y Waves Trans.: Off, 25%,50%,75% This essential
feature assists with the calibration of professional video cameras. It shows
the overall brightness of the image assisting the video professional in
correcting exposure. The waveform feature also checks the evenness of the
lighting when lighting a chromakey or background. ON, OFF Shows how saturated
the image is and where the pixels in the image land on the color spectrum.
Histogram: ON, OFF Mode: RGB1, RGB2, Y Y Histogram A quantitative tool to
check the picture brightness, display different color for different brightness
RGB Histogram It can display the graphic of color tone distribution, can
intuitively display the exposure status of the image, and display overlapping
histograms in red, green, and blue channels ON, OFF Focus Color: Red, Green,
Blue After turned on, the Focus Level (1 10) and Focus Color can be adjusted.
It highlights the areas that are in focus so you are able to quickly focus the
camera and not miss crucial shots. ON, OFF Display an audio diagram after
enabled to help you understand the audio status being used.
11
Embedded Audio
Over Exposure Check Field False Color Time Code
(Only Under SDI Signal)
Under HDMI Signal, max display 8 channels Mode: pr1, gp1, gp2, gp12 Audio Out: ch1-2, ch3-4, ch5-6, ch7-8 pr1 display1-2 channel, gp1 display 1-4 channel, gp2 display 5-8 channel, gp12 display 1-8 channel Under SDI Signal, max display 16 channels Mode: pr1, gp1, gp2, gp12, gp3, gp4, gp14 Audio Out: ch1-2, ch3-4, ch5-6, ch7-8, ch9-10, ch11-12, ch13-14,ch15-16 pr1 display1-2 channel, gp1 display 1-4 channel, gp2 display 5-8 channel, gp12 display 1-8 channel, gp3 display 9-13 channel, gp4 display 14-16 channel, gp14 display 1-16 channel ON, OFF After the exposure is turned on, the Exposure Level (10RE 100IRE),, can be adjusted. On, Off Mode: red, green, blue, gray When enabled, hue and saturation adjusted quickly and accurately. ON, OFF Mode: Normal, ARRI An image that depicts an object in colors that differ from those a photograph (a true color image) would show. ON,OFF Mode: LTC, VITC Same as camera time code consists of four groups of numbers, which respectively represent hours, minutes, seconds and frames. Through the time code, you can quickly find a specific frame in the video, so that in the later multi-camera editing, you can use the time code function to quickly align the video materials shot at different camera positions at the same time,
12
saving post-production time.
Marker
Grids Safe Frames Center Marker
Ratio Marker
ON, OFF
Mode: 2×2, 3×3, 4×4, 5×5, 6×6, 7×7, 8×8, 9×9 Color: Red, Green, Blue, Black,
White, Gray
The area of the picture can be divided into 4 ,9, 16, 25, 36, 49,64,81 equal
grids. ON, OFF Mode: 80%, 85%, 90%, 93%, 96%, 2.35:1 Marker Line Color: Red,
Green, Blue, Black, White, Gray ON, OFF Marker Line Color: Red, Green, Blue,
Black, White, Gray
ON, OFF Mode: 4:3, 13:9, 14:9, 15:9, 16:9, 1.85:1, 2.35:1 Marker Line Color:
Red, Green, Blue, Black, White, Gray Modified Mark: 0~5
Image
Scan Mode Aspect Ratio
Under Scan, Over Scan
Auto, 16:9, 16:10, 4:3, 5:4, 1.85:1, 2.35:1, Full Screen
ON, OFF Mode: 1.33x, 1.6x, 2.0x, 2.0x mag, User
13
Anamorphic Image Flip
Zoom Mode
Under User, you can custom adjust nx (1.20x~2.00x) Allows you to use
anamorphic lenses or adapters and see the image unsqueezed, even if your
camera does not de-squeeze in camera.
ON, OFF Mode: H Flip, V Flip, H_V Flip
ON, OFF Mode: 2X, 4X, 9X, 16X, User Under User, you can adjust 100%~200% It is
HD signal in any part, an amplification for high quality close-up.
Image Freeze
P2P (Pixel to Pixel)
ON, OFF
ON, OFF Enable the filmmaker to check the image from the 1:1 signal source
without scaling.This feature is essential for capturing optimum detail.
User Option
ON, OFF
LUT is a table for quickly looking up and output specific color
LUT
data. By loading different 3D-LUT tables, it can quickly
recombine color tone to form different color styles.
LUT Import: Confirm
LUT Table: display the built in SLOG2, SLOG3, LOGC,
VLOG and the custom LUTs
14
HDR Display Adjustment
Color Adjustment
HDR: ON, OFF Mode: HLG1, HLG2, HLG3 HDR can provide more dynamic range and the details of image, it is better to reflect the visual effects in the real environment. Backlight: 0~100 Adjust the screen brightness Brightness: 0~100 Adjust the image brightness Contrast: 0~100 Adjustment of the ratio between the brightest and darkest parts of the image . When adjusting, pay attention to the sense of hierarchy in the image. If the proportion is too large or too small, it can cause the image to lose its colorful appearance. Saturation: 0~100 Adjustment of color concentration Tint: 0~100 It is the most accurate standard for distinguishing various different colors. Determine what a certain color is actually color via the color appearance. Color Temp.: 5600K, 6500K, 9300K, User Under the “user”, the red, green, and blue values of the image can be adjusted (0~255)
Shortcut Key
F1~F4 Shortcut List: All Waves, Waveform Vector, Histogram, Embedded Audio,
Center Marker, Safe Frames,Grids, Focus Assist, False Colors , Over Exposure,
Anamorphic, Image Flip, Aspect Ratio Set the shortcut function
15
Left Right Key Set
e.g.: Using the MENU knob to select and confirm. Enter main
menu –User Option–Shortcut Key–F1 select one of pop-up functions, such as “All
Waves”, press confirm after selected
and the icon show light gray. Then when you exit menu, you
could press F1 directly on the front of panel to turn on “All
waves” function. Same setting for F2~F4 Backlight, Volume After selecting one
of them, when the menu is not displayed, rotate the MENU knob can directly
adjust
System
Language OSD Option
Volume
English, , Español, Português, Français,
Nederlands, Deutsch, , , ,
OSD Time: off, 15s, 30s, 45s Select the display time of the menu on the screen
OSD Trans: OFF, 25%, 50%, 75% Adjust the transparency of the menu picture
background on the screen. No Signal: Red, Green, Blue, Black, White, Gray
Mute: ON, OFF Volume: 0~100 Adjusting the speaker volume
After confirmed, the system back to original setting.
16
Reset Firmware Update
Firmware Version FTY CAL: On/Off Confirm Each monitor has color calibration
before ex-factory, the factory calibration button turn on by default. After
turning off, the monitor will without has color calibration, suggest don’t
turn it off. How to upgrade? 1. USB flash driver format
Supports FAT32 2. After copying the update file to USB flash driver and
inserting it into USB port of the monitor, use MENU knob to select Confirm and
press to update.
3. The monitor will turn off automatically after finishing, please turn on
manually 4. Check the firmware version whether the latest one
5. How to Import Custom LUT
5.1 USB flash driver format Supports FAT32
5.2 Max Files Limit Maximum 32 Lut files
5.3 File requirements The LUT file format suffix should be .cube Single file
not exceeded to 7.9Mb Support LUT-3D-Size 16,17,32,33,64,65
Remark: LUT file name must be English or Arabic numerals
5.4 Steps for loading
17
5.4.1 Make sure the USB flash driver correctly insert
5.4.2 Enter main menu User Option–LUT– Import — Confirm to load the monitor
will auto detect the USB flash driver
If there is valid LUT file in USB flash driver, the monitor will load LUT
files and show “[n] name. The [n] shows the quantity number. The “name” should
in LUT files’ name. If load successful, the screen will show “complete[n]”.
[n] Stands for the quantity number for LUT files should under 32.
PS: How to clear up the imported LUTs?
Insert a empty USB flash driver to the monitor, enter main menu User
Option–LUT– Import — Confirm, the imported LUTs will be clear up.
6. Support Signal Format
HDMI SDI
720p(60/59.94/50/30/29.97/25/24/23.98) 1080i (60/59.94/50
1080p(60/59.94/50/30/29.97/25/24/24sF/23.98/23.98sF) 4K 3840×2160p
(60/50/30/29.97/25/24/23.98Hz) 4K 4096×2160p (60/50/30/29.97/25/24/23.98Hz)
720p(60/59.94/50/30/29/25/24/23.98) 1080i(60/59.94/50) 1080p
(60/59.94/50/30/29.97/25/24/24sF/23.98/23.98sF)
7. Parameters
Panel Size Resolution Dot Pitch (mm)
21.5 2139.280×1080 109.22407×91508(W0 ) X 0.24795 (H) mm
18
Aspect Ratio Brightness Contrast
Viewing Angle
Backlight Inputs Outputs Upgrade/LUT IAmupdoiort Input Voltage Power
CSpoencsiuaml Fputinocntion Working TSetomrpagereature TUenmitpSeirzaeture
Unit Weight
16:9 1160:090cd/m² 215000c0d:1/m² 1000:1 89°/89°(L/R) 89°/89°(U/D)
LED 23G-SDI , 2HDMI 2.0, DVI-I, Tally 23G-SDI, 1HDMI 2.0 USB2.0 Speakers,
3.5mm Headphone Jack DC 1024V 44W TALLY Indicators 0 50 -20 60
553.5×394.5×115mm 9.25kg
8. Trouble Shooting
If there is any problem when using the unit, please try following ways to
inspect and solve. Please contact us if you still cannot solve it or have
other problems.
Without image display Video cable off or connect
incorrectly Without video signal input
Trouble shooting Check the quality of the cable, make sure the correct input interface Check the signal source and output interface
19
Monitor cannot be powered on
Supply voltage instability self-contained power supply,
polarity connect inversely
connect is corrected or not Check whether the power is connected, put the
power switch to “on” position The power adapter or battery is poor connected
with battery plate
Reference “Power input way” reconnect
Image/color display abnormal
Trouble shooting
Video cable poor contact
Change video cable, try again
Video signal interfered by
Move to another environment to try again
external environment
Video input signal amplitude too Check signal source video output, or change signal
low
source and have a try.
Menu color saturation
Enter menu to check color, or reset to factory
adjustment closing
settings
Check Field set in mono or black Reset Check Field, back to the color
& white
Image deformation
Reset the image ratio
Speaker without sound Audio cable off or improper
connection Volume adjustment was
closed HDMI cable poor Connected
No sound after switch video signal
Trouble shooting Confirm connected with the corresponding input port Reset the
volume control and adjust to a proper position Check the quality of cable, or
change cable and have a try This monitor is with audio signal only in audio
input and HDMI state
20
Remark: If there are still other problems, please contact with our related
technical persons. If there are changes without prior notice.
21
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>