Micron Electronics Pod Lite Tracker User Manual

June 6, 2024
Micron Electronics

Micron-logo

Micron Electronics Pod Lite Tracker

Micron Electronics Pod Lite Tracker product

 Introduction

Pod Lite uses primary batteries. it is a powerful GPS locator which is designed for vehicle and asset tracking. With superior receiving sensitivity, Its location can be real-time or schedule tracked by a backend server or specified terminals. Based on the embedded wireless tracking protocol, Pod Lite can communicate with the backend server through the LTE Cat-M network, and transfer reports of emergency, Geo-fencing, device status scheduled GPS position, etc…The service provider is easy to set up their tracking platform based on the functional wireless tracking protocol. The WIFI function will be activated and report the MAC addresses once the device is in alerting state. The BLE function will be activated and scan the third-party BLE data or Beacon broadcast by custom setting or protocol.

 Product Overview

AppearanceMicron Electronics Pod Lite Tracker
Fig1

LED Description

Micron Electronics Pod Lite Tracker
Fig2

There is one tricolor LED light in the Pod Lite device, the description is as follows.

Light Event State
LED show blue GPS fixed Solid
LED show red low power Solid
LED show green standby mode Slow Flash
During Call Solid

Getting Started

Parts List

Micron Electronics Pod Lite Tracker Fig 9

How GPS position Fix

Your device has an unobstru cted view of the sky, lying face up, so it can obtain the initial GPS FixMicron Electronics Pod Lite Tracker
Fig3

Disassemble Introduction

  1. .Dismantling machine tools Tweezers Cross Screwdriver
  2. Machine appearance:Micron Electronics Pod Lite Tracker Fig4
  3. Unscrew coverMicron Electronics Pod Lite Tracker Fig5
Insert SIM Card

Micron Electronics Pod Lite Tracker
Fig6

Device Power on

Micron Electronics Pod Lite Tracker
Fig7

InstallMicron Electronics Pod Lite Tracker Fig8

Troubleshooting and Safety inf

  • Troubleshooting****
Trouble Possible Reason Solution
Messages can’t be reported to the backend server by the Mobile network. APN

is wrong. Some

APN can not visit the internet directly.

| Ask the network operator for the right APN.
The IP address or port of the backend server is

wrong.

| Make sure the IP address for the backend server is an identified address

on the internet.

Unable to power

off Pod Lite.

| The function of the power key

was disabled by

| Enable the function of the power key by

AT+GTFKS.

 | AT+GTFKS.|
---|---|---
The battery can not be charged| The battery has not been used for a too long time and

has been locked.

| Using an external power source with a 3.65V DC power supply to active the

battery or apply for after-sale help.

Pod Lite can’t fix GPS successfully.| The GPS signal is weak.| Please move Pod Lite to a place with

open sky.

It is better to let the top surface face to the sky. (The same surface with

indication LED)

  • Safety info

The following items are suggestions for safety use, please pay more attention

  • * Please do not disassemble the device by
    • Please do not put the device in an overheating or too humid place, avoid exposure to direct sunlight. The too high a temperature will damage the device or even cause the battery explosion.
    • Please do not use Pod Lite on the airplane or near medical

FCC Caution

§ 15.19 Labelling requirements.

This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.

§ 15.21 Information to the user.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

§ 15.105 Information to the user.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  1. Reorient or relocate the receiving antenna.
  2. Increase the separation between the equipment and receiver.
  3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  4. Consult the dealer or an experienced radio/TV technician for help.

The main use site of this device is fixed in the container of large trucks or trucks. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals