Brolux 03345 LED Luminaire Cynideco Instructions

Brolux 03345 LED Luminaire Cynideco

INSTRUCTION MANUAL

1. METHODS OF INSTALLATION

1. Insert the mounting pins in the place where the lamp is to be installed.
2. Screw the fixture to the surface.
3. Connect the power.
4. Replace the front cover.

2. DIMENSIONS

3. POWER CONNECTION

CAUTION

Turn off the power before installation or maintenance.

Switch off the power supply before installation or maintenance. Turn off the power before installation or maintenance. Turn off the power before installation or maintenance.

The product will automatically turn off if the lamp starts to overheat and turn on again after cooling down.

This product will automatically shut down once the temperaturÿ goes too high and will automatically turn on once it cools down.

This product will automatically turn off once the temperature is too high and automatically turn on when it cools down. This product will be automatically soaked if the temperature is too high and automatically soaked if cold.

Read the manual before installation.

Supply voltage – 100-277V 50Hz AC Input
voltage – 100-277V 50Hz AC.
Input voltage – 100-277V 50Hz AC.

Wire markings:

Brown – (L), Blue – (N), yellow-green – ground.

Dust or other dirt should be removed using microfiber cloths.

Remove the dirt & dust with microfiber wipes.

Avoid looking directly at the LED sources.

Replace broken glass.

Do not cover with insulating material.

Do not use the product in places not suitable for it.

The product should not be used in ambient conditions that threaten the structure, paint coating or electrical equipment installed in the lighting fixture. These conditions include: high humidity, temperature, dust, presence of non-neutral chemicals in the air, UV radiation and shocks and vibrations

Do not use this product in environmental conditions which endanger construction, paint coat, electrical equipment of luminarie. This conditions are high humidity, high temperature, dustiness, the presence of non- indifferent chemical substances in the air, UV radiation, shocks and vibrations. or electrical components of the luminaire. These conditions are high humidity, high temperature, dust, uneven chemicals in the air, ultraviolet radiation, shock and vibration. Do not vikorist this virib in the minds of too much middle ground, which will threaten everyday life, electricity, candles.

This means high humidity, high temperature, saw, the presence of unknown chemical substances in the wind, ultraviolet vibration, impact and hammering.

Do not use this product in environmental conditions that endanger the construction, the paint layer, the electrical equipment of the lighting. These conditions are high humidity, high temperature, dust, the presence of non- indifferent chemicals in the air, UV radiation, shock and vibration.

Do not use the product in special conditions.

Carrying out any activities inside the luminaire with the power on may result in electric shock.

Making any work inside the housing with the power on may cause an electric shock.

Any work inside the cabinet when it is switched on can cause electric shock.

Doing any work inside the case with the power on may cause an electric shock.

Any work inside the enclosure with power on may result in electric shock.

The manufacturer is not responsible for any defects caused by not following the instructions in this manual.
Making any work inside the housing with the power on may cause an electric shock.
These luminaires are for indoor use only.

Dealing with used frames:

LED lamps (luminaires) must be disposed of in accordance with currently applicable environmental protection regulations. Used fixtures should be returned to the appropriate collection point, where they will be accepted free of charge. Correct disposal of electrical equipment allows you to preserve valuable natural resources and avoid negative effects on health and the environment, which may be threatened by inappropriate waste management.

Product Specifications:

• A [mm]: 5385
• B [mm]: 1200
• C [mm]: 70
• Weight: 40 grams

Product Usage Instructions:

Installation:

1. Insert the mounting pins in the desired location for lamp installation.
2. Securely screw the luminaire onto the surface.
3. Connect the power supply following the cable markings: brown -(L), blue – (N), green/yellow – ground.
4. Replace the front cover of the lamp.

Handling of Used Luminaires:

Disposed of used lamps or LEDs in compliance with environmental regulations. Return worn-out luminaires to designated collection points for proper disposal.

FAQ:

Q: How should I dispose of used luminaires?

A: Follow current environmental regulations and return worn-out luminaires to appropriate collection points for free disposal.

Q: What are the cable markings for power supply connection?

A: Cable markings are brown – (L), blue – (N), green/yellow -ground.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>