HOOKE ROAD BXG.8929-S Roof Rack Installation Guide

HOOKE ROAD BXG.8929-S Roof Rack

Product Information

Specifications:

• Model: BXG.8929-S
• Contents:
  • 36 Button Head Socket Cap Bolts Screws M8*16
  • 4 Button Head Socket Cap Bolts Screws M8*25
  • 12 Button Head Socket Cap Bolts Screws M6*20
  • 4 Button Head Socket Cap Bolts Screws M6*16
  • 8 Button Head Socket Cap Bolts Screws M6*10
  • 40 Flat Washer M8201, M6161, M6121
  • 12 Flange Hex Lock Nuts M8, 16 Flange Hex Lock Nuts M6
  • 8 Tee Sliding Slot Nuts M6
• Tools required:
  • 4mm & 6mm Hex Bit Socket
  • Drive Socket Ratchet Wrench
• Installation time: About 2 hours, 2-3 people may be needed.

Installation Instructions:

1. Step 1: Open the package and verify all parts are present. Assemble the rear half by connecting rear side rails and faring using M8*16 screws and nuts.
2. Step 2: Assemble three crossbars in the rear section using M8*16 screws and washers.
3. Step 3: Install brackets, distinguishing between outer and inner brackets. Differentiate left and right sides based on bracket shape.
4. Step 4: Install rear mounting bracket in the rear section using M8*25 screws, washers, and nuts without overtightening.
5. Step 5: Secure rear mounting bracket into vehicle’s recess and tighten installation screws.
6. Step 6: Assemble the front part by installing the short crossbar into the front faring with Tee Sliding Slot Nuts and screws.
7. Step 7: Install front mounting bracket onto front panel without tightening screws.
8. Step 8: Place the assembled front faring into the vehicle and secure with factory bolts.
9. Step 9: Install side rails on both sides of the front faring using specified screws, washers, and nuts.
10. Step 10: Install four crossbars into the front half part and tighten screws.
11. Step 11: Connect front and rear sections using connecting brackets and specified screws and washers.
12. Step 12: Installation is complete. Enjoy your off-road adventures!

Frequently Asked Questions (FAQ):

1. Q: How do I know if I have assembled the roof rack correctly?
   A: Ensure all parts are securely fastened according to the instructions provided in the manual. Check for any loose components or misalignments before usage.

2. Q: Can the roof rack be installed on any type of vehicle?
   A: The roof rack is designed to be compatible with specific vehicle models. Please refer to the compatibility list or contact customer support for more information.

3. Q: Is it necessary to use all the provided bolts and nuts during installation?
   A: Yes, it is crucial to use all the specified bolts, nuts, and washers during installation to ensure the structural integrity of the roof rack.

Tools required:

• 4mm & 6mm Hex Bit Socket;
• Drive Socket Ratchet Wrench；

Installation time:
About 2 hours, 2-3 people may be needed. Installation time may differ according to your mechanical skill level.
(PLEASE VERIFY ALL PARTS ARE PRESENT AND READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION!)
To view the electronic version (BXG.8929-S), please scan the QR code.

Installation instruction

Step 1: First, please open the package to ensure that you have received all the accessories. This roof rack is divided into two parts, front and rear. Assemble the rear half first, then connect the rear side side rails and rear faring using M8*16 screws and nuts.

• (4) M8*16 Button Head Socket Cap Bolts Screws
• (4) M8201 Flat Washer
• (4) M8 Flange Hex Lock Nuts

Step 2: Assemble the three crossbars in the rear section using M8*16 screws and washers together.

• (12) M8*16 Button Head Socket Cap Bolts Screws
• (12) M8201 Flat Washer

Step 3: When installing the brackets, distinguish between the outer bracket and the inner bracket. The outer bracket is larger than the inner bracket. Differentiate between the left and right sides based on the shape of the bracket’s end. The angled edge is for the driver’s side, while the right angle is for the passenger side.

Step 4: After identifying the respective positions of the brackets in the previous step, install the rear mounting bracket in the rear section using M8*25 screws, washers, and nuts together, but do not tighten the screws too much.

• (4) M8*25 Button Head Socket Cap Bolts Screws
• (4) M8201 Flat Washer
• (4) M8 Flange Hex Lock Nuts

Step 5: Lift the assembled rear half of the roof rack and secure the rear mounting bracket into the vehicle’s recess. Tighten the bracket’s installation screws once it is fully inserted.

Step 6: Assemble the front part. Install the short crossbar into the front faring. First, place the Tee Sliding Slot Nuts inside the grooves of the short aluminum bars, align them with the holes on the front faring, and secure them using M610 screws and M612*1 flat washers.

Step 7: Install the front mounting bracket onto the front panel using M616 screws and M6121 washers and nuts, but do not tighten the screws.

• (4) M6*16 Button Head Socket Cap Bolts Screws
• (4) M6121 Flat Washer
• (4) M6 Flange Hex Lock Nuts

Step 8: Remove the cover above the front glass of the original vehicle, Put the assembled front fairing into your vehicle. Install it into your vehicle with the factory bolts.

Step 9: Next, you need to install the side rails on both sides of the front fairing, using M8*16 screws, washers, and nuts for assembly.

• (4) M8*16 Button Head Socket Cap Bolts Screws
• (4) M8201 Flat Washer
• (4) M8 Flange Hex Lock Nuts

Step 10: Install four crossbars into the front half part using M6*16 screws and washers, and tighten the screws.

• (16) M8*16 Button Head Socket Cap Bolts Screws
• (16) M8201 Flat Washer

Step 11: Finally, connect the front and rear sections using the connecting brackets. Use M612 screws and M616*1 washers and nuts for assembly. Each side requires two connecting brackets, and an inner connecting bracket should also be installed.

Step 12:
The installation is complete. We hope you enjoy a wonderful off-road life with this quality Hooke Road product!

Attention:

1. The product parts in this instruction may differ slightly from the actual product contents but generally does not affect the installation of the product.
2. Please feel free to contact your distributor if you have any kind of question about your purchase.

Google Hooke Road to find your parts.
Feel Free To Share Your Vehicle @HookeRoad4x4 With The Hashtag #hookeroad If You’d Like

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>