HOOKE ROAD BXG.2075-S Wrangler JK 4 Doors Off Road Tube Half Doors Tubular Front and Rea User Manual

June 2, 2024
HOOKE ROAD

HOOKE ROAD BXG

HOOKE ROAD BXG.2075-S Wrangler JK 4 Doors Off Road Tube Half Doors Tubular

Front and Rear User Manual

Front and Rear Tube Doors BXG.2075-S

(1) Contents:

FIG 1 Contents.jpg

FIG 2 Contents.jpg

FIG 3 Specification.JPG

(2) Tools required:

a. Drive Socket Ratchet Wrench;
b. 13mm Wrench;
c. 5mm Hex Bit Socket;

(3) Installation time:

About 40 minutes, 1-2 people may be needed. Installation time may differ according to your mechanical skill level.
(PLEASE VERIFY ALL PARTS ARE PRESENT AND READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION!)
To view the electronic version (BXG.2075-S), please scan the QR code.

FIG 4 Installation time.jpg

(4) Installation instruction:

Step 1:
Disconnect wiring harness before removing the door. Remove the plastic cover at the base of the B-pillar to access the electrical connector. Release the red locking tab and pull down on the connector. Next, remove the strap from the hook located inside the vehicle. NOTICE! The door can swing freely once the strap is released potentially causing damage to your vehicle. Do not let go of the door when the strap is disconnected.

Step 2:
Remove the Torx nut from the bottom of each factory hinge pin. Set these nuts aside to be re-installed on the Half Doors. To remove the factory doors, carefully lift the door upward until the hinge pins completely clear the hinges. It will be helpful to have someone else assist with this step.

Step 3:

Lay the door on the ground, use a blanket or big cardboard between the door and the ground to keep the outside of the door from scratch.

Step 4:
Confirm the right hinge installed in the right position, there are the positions you can figure out shown below. (Make sure you installed right hinge on the right position, you can compare with picture showed below).

FIG 5.jpg

FIG 6 Installation instruction.jpg

Attention : The strap at the lower part of doors, they have installed with straps at back. Don’t forget to install it. Showed Below.

FIG 7 Installation instruction.jpg

Step 5:
Build up door assembly. Install the Hinges and other parts on the door.
A. The Front door assembly installation.

FIG 8 Installation instruction.jpg

(1)(2)Install the front upper hinge with the screws in the package.
(3)(4)Install the front lower hinge with the screws in the package.

B. Tie the shade skins. As the picture shown.

FIG 9 Installation instruction.jpg

C. The Front door Installation

FIG 10 Installation instruction.jpg

(5) Slide the door onto the factory hinge pins. Tighten the hinge bolts while the door is closed.
(6) Place the strap over the top of the retaining hook and make sure the door is secured.
Then the Front door installation is over.

Step 6:
The Rear door installation. The difference between Front and Rear door installation is the strap (the length of the rear strap is longer than the front).
Following work is just seem like the Front door.

Step 7:
The installation is complete. We hope you enjoy a wonderful off-road life with this quality Hooke Road product!

Attention:

  1. The product parts in this instruction may differ slightly from the actual product contents but generally does not affect the installation of the product.
  2. Please feel free to contact your distributor if you have any kind of question about your purchase.

FIG 12.JPG

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

HOOKE ROAD User Manuals

Related Manuals