LITETRONICS FLATM2 Flood Light Trunnion Mount Instruction Manual
- June 2, 2024
- Litetronics
Table of Contents
LITETRONICS FLATM2 Flood Light Trunnion Mount
Product Information
Specifications
- Model: Flood Trunnion Mount (FLATM2)
- Compatible with: 100W & 150W flood lights
- Includes: Trunnion Mount, M8 16mm (x4), M8 25mm (x2), M8 Spring Washer (x8), M8 Flat Washer (x10), M8 Lock Nut (x4), M5 * 16mm (x2), Ground Washer (x1), Expansion Bolts (x2)
Product Usage Instructions
Safety Instructions and Warnings
Before Installation, carefully remove all parts from the packaging. Inspect
the product for defects due to shipping. Always turn off the power supply from
the main circuit breaker first!
Trunnion Bracket Installation
- Open the mount head. (Refer to Figure 1)
- Run the input wire through the hole in the trunnion base. Affix the base with screws and lock to the fixture. (Refer to Figure 2)
- Pass the wires through the trunnion mount head. Install the mount head and keep the screws loose. (Refer to Figure 3)
- Finish the wire connection accordingly (refer to flood light installation instructions for the wiring diagram).
- Align the fixture to the required angle. Tighten screws after confirming the angle. (Refer to Figure 4)
- Turn the power back on.
FAQ
-
Q: What tools are required for installation?
A: Allen Wrench -
Q: How can I contact customer service for further assistance?
A: You can reach out to Customer Service at customerservice@litetronics.com or call 1-800-860-3392. -
Q: Where can I find updated versions of the installation instructions?
A: Visit www.litetronics.com for any updated versions of the instructions.
SAFETY INSTRUCTIONS AND WARNINGS
- When using electrical equipment, basic safety precautions should always be observed.
- This product must be installed by the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
- Installation should only be conducted by a qualified electrician by NEC and any relevant local building codes.
- Be certain electrical power is OFF before and during installation and maintenance.
- To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or sharp objects
WHAT COMES IN THE BOX
- Trunnion Mount
- M8 * 16mm (x4)
- M8 * 25mm (x2)
- M8 Spring Washer (x8)
- M8 Flat Washer (x10)
- M8 Lock Nut (x4)
- M5 * 16mm (x2)
- Ground Washer (x1)
- Expansion Bolts (x2)
- Installation Instructions
REQUIRED TOOLS
- Allen Wrench
INSTRUCTIONS
Before Installation, carefully remove all parts from the packaging. Inspect product for defects due to shipping. Always turn off the power supply from main circuit breaker first!
TRUNNION BRACKET INSTALLATION
- Open the mount head. (Figure 1)
- Run the input wire through the hole in the trunnion base (watch out not to scratch the wire). Affix the base with screws and lock to the fixture. ( Figure 2)
- Pass the wires through the trunnion mount head (watch out not to scratch the wire). Install the mount head and keep M5 and M8 screws loose. (Figure 3)
TRUNNION MOUNT FIXTURE INSTALLATION
- Finish the wire connection accordingly (refer to flood light installation instructions for the wiring diagram).
- Align the fixture to the required angle. Tighten M5 and M8 screws after the angle is confirmed. (Figure 4)
- Turn the power back on.
Note : The adjustable angle is 0~+/-90 °. (Figure 4)
Thank you for choosing
6969 W. 73rd Street
Bedford Park, IL 60638
WWW.LITETRONICS.COM
CustomerService@Litetronics.com or
1-800-860-3392
The information and product specifications contained in these instructions are based upon data believed to be accurate at the time of printing. This information is subject to change without notice and without incurring liability. If you have questions regarding specific product details, please contact us at 800-860-3392 or via email at customerservice@litetronics.com. To check for an updated version of these instructions, please visit www.litetronics.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>