BELLEVUE MVLCH52302MBK Pytharatus 4 Light 34 Wide Linear Chandelier Instruction Manual

Instruction Manual

MVLCH52302MBK Pytharatus 4 Light 34 Wide Linear Chandelier

Tools Required (not included): Flathead screwdriver, Phillips screwdriver, Wire cutters, Electrical tape, Safety goggles, Ladder, Pliers.
Helpful Tools (not included): Wire strippers
Bulb Recommended: (4) GOW Type-S medium base vintage-style bulb, Alternate (4) LED bulb.
Estimated Assembly Time: 20 – 30 minutes
Preparation:

• Identify and inspect all parts before beginning installation
• Check package contents list and diagrams below to be sure all parts are included.
• If any parts are missing or damaged, do not attempt to assemble, install or operate the fixture.

Warnings And Cautions

• Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
• These instructions are provided for your safety. Itis very important you read them completely before installing fixture. We strongly recommend that a licensed, professional electrician perform the installation.
• Disconnect fixture from power source before replacing bulbs.
  – Make sure bulbs are given sufficient time to cool before removal.
  – Do not subject glass parts to any shock while in operation or shattering may result.

Package Contents

STEP 1:
a. Secure the crossbar to the outlet box (not included) with outlet box screws.
b. Tighten until snug.
Note: The preassembled mounting nipple on the crossbar should protrude outward. ![BELLEVUE MVLCH52302MBK Pytharatus 4 Light 34 Wide Linear Chandelier

• Figure 8](https://manuals.plus/wp-content/uploads/2024/03/BELLEVUE- MVLCH52302MBK-Pytharatus-4-Light-34-Wide-Linear-Chandelier-Figure-8.png)STEP 2:
  a. Remove lock ball and hex nut from crossbar assembly.
  b. Fit ceiling canopy over the nipple on crossbar assembly and secure with lock ball.
  Note: The ceiling canopy should be snug against the ceiling and the lock ball.

  • If not, adjust the length of the nipple on the crossbar assembly by unscrewing the preassembled hex nut.
  • Then, screw the nipple in or out of the crossbar until the desired length is achieved.
  • Once the ceiling canopy is secure, remove the lock ball and ceiling canopy and proceed to Step 3.

STEP 3:
a. Choose desired hanging length for the light fixture.
b. Assemble the necessary rods using the 6 inch rod(s) and/or 12 inch rod(s). Extra Fixture Chain might be required for higher ceiling.
c. Pass supply wires and ground wires through the rod assembly.
d. Attach the rod assembly, the fixture loop, the quick link to fixture.
Hand- tighten until snug.
Hint:
– Assemble one rod ata time.
– Pass the ground wire through the rod first.
– Then, pass the supply wire through the rod.
– Thread the rod by hand until snug.
– Thread the fixture loop to the uppermost rod.
– Connect one end of the Fixture Chain to the loop preassembled to ceiling canopy with one quick link.
– Connect the other end of the fixture chain to the fixture loop with the remaining Quick Link. Suggested rod length to hang fixture 30 inches above table top:
– 8 ft. Ceiling (2) 12 inch rods + (4) 6 inch rods + 2 quick links
– 9 ft. ceiling (4) 12 inch rods + (4) 6 inch rods + 2 quick links
– 10 ft. ceiling (6) 12 inch rods + (4) 6 inch rods + 2 quick links
– 11 ft. ceiling (6) 12 inch rods + (4) 6 inch rods + 12 inches of chain + 4 quick links
– 12 ft. ceiling (6) 12 inch rods + (4) 6 inch rods + 24 inches of chain + 2 quick links

STEP 4:
a. Confirm that the mounting height is acceptable. Refer to STEP 3 if changes are required.
Note: To make the next step easier, cut the supply wire and ground wire 24 inches longer than the distance from the fixture loop to the ceiling. Important: Please pay attention to the polarity (wires labels L& N) when cutting wires. Wire identification will be  needed in STEP 6.
b. Pull the Supply Wires and Ground Wire up through the Fixture Chain alternating links.
c. Push the ends of the supply wires and ground wire up through the canopy loop and into the outlet box. The remaining slack wire will be pushed into the box in STEP 5. STEP 5:
a. The lanyard is provided as a means to support the fixture from the junction box while connecting the electrical wires. This enables the fixture to hang from the junction box and your hands are free to make the wire connections.
b. Turn the button stop so it may be inserted into the crossbar slot. Make sure the button stop is completely inside the crossbar.
c. Slowly release the fixture to make sure it is supported by the button stop.
d. Proceed to Step 7. Once wiring is complete, the lanyard will push into the junction box when the Ceiling Canopy is attach to the ceiling. STEP 6:
* Use Wire Connectors (supplied) to connect the wires.
a) Ground Wire:

1. Wrap supply ground wire around green ground screw on mounting bracket, no less than 2 in. from the end of the wire. Tighten ground screw.
2. Connect fixture ground wire to supply ground wire with wire connector.

b) Supply Wire:

1. Connect the supply white wire to the fixture supply wire (ribbed sided) from fixture identified with the label “N”.
2. Connect the supply black (or red) wire to the fixture supply wire (smooth side) from fixture identified with the label “L”.
3. Wrap each connection with approved electrical tape and carefully stuff all of the connected wires into the outlet box.

STEP 7:
A. Re-attach the ceiling canopy to the crossbar assembly.
b. Secure with the previously removed hex nut.
c. Then, attach the lock ball over the ceiling canopy. STEP 8:
a. Install correct bulbs referring to fixture markings and/or labels for maximum wattage.
Your installation is completed now. Restore electricity. Retain this sheet for future reference.

CARE AND MAINTENANCE

Wipe clean using soft, dry cloth or static duster. Always avoid using harsh chemicals and abrasives to clean fixture as they may damage the finish.

TROUBLESHOOTING

2. Power is off.
3. Faulty wire connection.
4. Faulty switch.| 1. Replace light bulb.
2. Make sure power supply is on.
3. Check wiring.
4. Test or replace the switch.
Fuse blows or the circuit breaker trips when light is turned on.| Crossed wires or power wire is grounding out.| Check wire connection.

Printed in China

Documents / Resources

| BELLEVUE MVLCH52302MBK Pytharatus 4 Light 34 Wide Linear Chandelier [pdf] Instruction Manual
MVLCH52302MBK Pytharatus 4 Light 34 Wide Linear Chandelier, MVLCH52302MBK, Pytharatus 4 Light 34 Wide Linear Chandelier, 4 Light 34 Wide Linear Chandelier, 34 Wide Linear Chandelier, Linear Chandelier, Chandelier
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>