Arashi AAP 401 Air Purifier User Manual
- May 15, 2024
- Arashi
Table of Contents
Arashi AAP 401 Air Purifier
Specifications
| Type | Arashi Air Purifier AAP 401 |
|---|---|
| Voltage | 220V – 240V / 50Hz |
| Power | 52W |
Touch Panel
- UV-C Lamp
- Child Lock
- Anion
- HEPA H13 Filter
- Low Noise Level
- 4-Stage Air Filtration
- Indicator to replace Filter & Function Panel
Warnings
- Keep away from liquids or easily ignited objects.
- Do not clean the unit with flammable liquids or air sprays.
- Do not insert any foreign objects into the air outlet/inlet.
- Do not plug or unplug the AC cord with wet hands.
- Before cleaning or maintenance, unplug the AC cord from the outlet.
Attention
- Remove the filter cover before installation.
- Check the filter position before using the unit.
- Ensure that the voltage and power source match; otherwise, the old electrical track may become hot and cause accidents.
- Do not use the unit as a kitchen exhaust.
Product Technical Features – Purification Technology
- Pre-Filter captures particles before they enter the Hepa Filter.
- H13 Hepa Filter efficiently filters PM 2.5 and has a filtration efficiency of over 99.9%.
- Activated Carbon Filter absorbs formaldehyde, benzene, and other pollutants.
- Three settings for timer operation: 2, 4, and 8 hours.
- Quiet design with three fan speeds: Low, Medium, and High.
- Sleep Mode: Operates quietly without disturbing sleep.
- Negative Ion function: Cleans the air of dust, smoke, and allergens.
- UV-C Lamp eliminates germs and bacteria in the air. Note: The UV-C Lamp is inside the unit and not visible, so it is safe for users and the surroundings.
Air Filtration Process Diagram
Illustrates the air passing through three stages: Pre-Filter, H13 Hepa Filter, and Activated Carbon Filter, resulting in clean air.
Control Panel
Description of the control panel with labels for Child Lock, Anion
function, UV-C Lamp, Timer buttons for 2, 4, and 8 hours, Fan Speed buttons,
and ON/OFF button.
Unit Placement
- Place the unit at least 30 cm away from walls and furniture.
- Ensure no foreign objects fall into the air outlet/inlet.
- Do not use in humid places or where the air is stagnant.
How to Use
- Connect the AC cord to a power source; the indicator light will flash once, and the unit will enter Standby mode after a beep.
- Press the Power button; the fan speed will change along with the Anion logo, and all indicators will light up. Press the Power button again to return to Standby mode.
- Press the Fan Speed button to change the fan speed.
- Press the Sleep button for 3 seconds to activate the Sleep filter; all lights except for the Sleep indicator will turn off, and the fan will run at low speed. Press any button to cancel Sleep mode.
- Use the Timer button to set the operating time (2/4/8 hours). The unit will turn off automatically once the set time is reached.
- Press the Child Lock button for 3 seconds to activate Child Lock; the Child Lock indicator will light up. To deactivate, press and hold the Function button for 3 seconds.
- To activate the UV-C and Anion functions, press the Function button; the process is as follows:
Filter Replacement
Filter should be replaced every 3-6 months, indicated by the Function indicator. To reset the filter usage time, press the Timer button for 3 seconds after replacing the filter.
Filter Replacement Procedure
- Turn off the unit and unplug the AC cord.
- Open the back cover.
- Remove the filter.
- Remove the protective plastic from the new filter.
- Install the new filter into the unit.
- Reattach the back cover.
Maintenance
- Always unplug the unit from the power source before cleaning or maintenance.
- Wipe the unit with a soft cloth; use a neutral detergent if necessary.
- If the cloth is too wet, wring it out before use.
- Do not use easily flammable liquids or corrosive cleaning agents.
- If the filter replacement indicator turns on, it means the filter needs to be replaced.
- After replacing the filter, press the Function button for 3 seconds to reset the filter usage time indicator.
Troubleshooting
| Problem | Solution |
|---|---|
| Unit does not work | Ensure the unit is properly installed |
| Cannot smell the fragrance | Open a window to allow air circulation, then turn |
on the unit. Check if the filter is properly installed or needs replacement.
Unit makes a loud noise| Check if the filter’s plastic packaging has been
removed. Check if the filter needs replacement.
Manufacturer and Distributor Information
Distributed by:
- PT. Tri Harmonis Niagantara – Jakarta
- PT. Citra Hannochs Niagantara – Medan
- PT. Arthatama Petilan Nusa – Surabaya
For consumer services, please contact layanankonsumen@hannochs.com
FAQ
How often should I replace the filter?
The filter should be replaced every 3-6 months or when the Function indicator lights up.
What does the Sleep Mode do?
Sleep Mode quiets the operation of the unit and sets the fan to a low speed for a disturbance-free sleep environment.
How do I reset the filter usage time indicator after replacing the filter?
Press and hold the Timer button for 3 seconds after replacing the filter.
Can I use the air purifier as a kitchen exhaust?
No, the unit should not be used as a kitchen exhaust.
What should I do if the air purifier makes a loud noise?
Check if the filter's plastic packaging has been removed and if the filter needs to be replaced.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>