Arashi ASB 1507 Stand Blender User Manual

Arashi ASB 1507 Stand Blender

SPECIFICATION

• Power: 350W-AC (220-240V/50-60Hz)
• Speed ​​Options: Pulse, 1 & 2
• Jar/Grinder/Chopper Material: USA
• Blade Material: Stainless Steel
• Cable Length: 1.2 meters

PARTS

• A. Inner cover
• B. Close
• C. Plastic Jar
• D. Jar Knife
• E. Motorcycle
• F. 2 Speed ​​Switch + Pulse
• G. Mixing Spoon
• H. Grinder / Grinder Bowl
• 1. Grinder Blade
• J. Grinder Connector
• K. Close the Cutter / Chopper Bowl
• L. Cutting Knife
• M. Cutting Bowl

NO. REGISTRATION: IMKG.2254.10.2020
For first use, please take the time to read the Instructions for Use carefully. Please observe all safety precautions and follow operating procedures.

USE

1. Please install the JAR correctly, so that the tool can function properly.
2. Place the large JAR (C) on top of the Motor and adjust until the JAR is in place position, turn the JAR slightly counterclockwise until it locks.
3. Cut the food ingredients into several pieces to be blended then add enough water without exceeding the marked 1L limit.
4. Attach the Lid (B) and turn to lock it.
5. Plug the tool into the socket and set the switch button (F) to the desired speed desired (One, Two, or pulse).
6. When mixing, we can add ingredients with pour them from the top lid.
7. When finished, turn the switch to setting 0 to stop and remove the JAR (C) by turning it clockwise.

IMPORTANT TO NOTE

1. Do not press the switch button of the unit with wet hands.
2. Do not add liquid or other food to it, while the unit is on is in operation.
3. Do not touch the blade with your hands when cleaning to avoid accidents/dangers.
4. Before using the unit, please check the voltage of your appliance with suitability of your home’s voltage.
5. Always turn off the unit before disconnecting the cord from the power source.
6. Never place/wash the unit & plug in water or put other fluids into the motor.
7. Turn off and remove the plug from the socket when it is no longer in use or before cleaning.
8. Keep out of reach of children.
9. Do not operate the unit if any part is damaged.
10. Take the tool to the nearest authorized dealer or service centre for repairs.

BLENDER

1. Do not fill the JAR with materials that are hot over 60 °C.
2. Do not load materials beyond the maximum level of the JAR to avoid spills.
3. Always insert the inner cover (A) into the cover (B) before You start to process.
4. Cut fruit and other solid ingredients into small pieces before being put into the JAR.
5. Hard materials must be processed in stages to make the Blender process easier.
6. Do not put your hands or other objects into the blender while the appliance is running turned on. If necessary, use a stirring spoon to remove food in the JAR after the appliance is turned off.
7. Before you start using this tool, make sure the blade is installed tightly to the tool.

CUTTER/CHOPPER

1. This unit has very sharp blades, please be careful.
2. Do not operate for more than 30 seconds without a break.
3. Make sure all components are installed properly and correctly.
4. This unit is not suitable for cutting hard objects such as seeds walnuts or ice cubes.
5. Suitable for cutting carrots, onions, garlic, etc. Before adding, cut the ingredients into small pieces first.

GRINDER

1. When grinding, pause every 30 seconds.
2. Always ensure that the rubber ring is installed correctly before using it.
3. Do not use grinders to process base raw materials liquid.
4. The grinder is not suitable for grinding very hard materials, such as nutmeg and ice cubes.

CAN BE USED FOR GRINDING & CUTTING

MATERIAL QUANTITIES

• Pepper: 25 – 75 gr
• Sesame Seeds: 25 – 75 gr
• Rice, Wheat: 25 – 75 gr
• Soybeans: 25 – 75 gr
• Dried Peas: 25 – 75 gr
• Coconut meat: 25 – 75 gr
• Coffee beans: 25 – 75 gr
• Dry Bread: 1 potong roti kering
• Rock Sugar: 50 gr
• Beans (shelled): 25 – 75 gr

CARE/MAINTENANCE INSTRUCTIONS

1. Always remove the plug from the socket, and remove other components after finished use.
2. Clean the JAR with water and cleaning fluid.
3. Clean other components of the unit with a soft, dry cloth.
4. Avoid any type of moisture on the motorbike.
5. Store the unit in a dry place after cleaning.

SERVICE

1. Do not operate the unit if it is not working/any parts are damaged.
2. Do not disassemble the damaged unit yourself, take it to an authorized dealer or Nearest Service Center for inspection, repair or replacement.

Misuse can make the warranty invalid

1. Unreasonable use.
2. Damage caused by electrical current disturbances.
3. The product broke due to falling.
4. The blender machine is getting water.
5. Damaging the seal (if the seal is damaged, the guarantee will no longer be valid).

CONTACT

• Distribution by:
• PT. Tri Harmonis Niagantara – Jakarta
• JI. Gedong Panjang No. 53, Ex. Penjaringan, District. Penjaringan City Adm North Jakarta, Prov. DKI Jakarta 14440
• PT. Citra Hannochs Niagantara – Medan
• JI. Prosecutor No. 5A-5B-5D, Ex. Middle Passage. District Medan Petisah, Medan City. Prov. North Sumatra 20112
• PT. Arthatama Pelita Nusa – Surabaya
• Jl. Kalianak Barat 51-D, Kel. Genting Kalianak, District. Asemrowo, Surabaya City, Prov. East Java 60183
• consumerservice@hannochs.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>