SUNFORCE 80073 18 Inch LED Solar String Light Installation Guide
- June 1, 2024
- SunForce
Table of Contents
SUNFORCE 80073 18 Inch LED Solar String Light
PARTS
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY, THIS ITEM IS INTENDED FOR OUTDOOR DOMESTIC USE ONLY. NOT FOR COMMERCIAL USE.
WARNING:
Prior to hanging the bulbs, make sure they do not rest upon any hot surface or where they could become damaged. If you are charging the batteries without attaching the bulbs, keep the bulbs in the retail box or safely store them indoors to prevent any potential damage.
CAUTIONS: SAFETY INFORMATION
- Your solar string lights are not a toy. Keep them out of reach of small children.
- Your solar string lights and solar panel are both fully weather-resistant.
- The solar panel must be mounted outdoors to maximize sun exposure.
- Prior to installation, lay out all components and check against the parts list section of this manual.
- Never look directly into the solar string lights.
- Do not hang any other objects on the solar string lights.
- Do not cut the wire or make any wiring changes to the solar string lights.
CAUTIONS: BATTERY INSTRUCTIONS
WARNING – KEEP BATTERIES OUT OF REACH OF CHILDREN.
- AJways purchases the correct size and grade of battery most suitable for the intended use.
- Always replace the whole set of batteries at one time, taking care not to mix old and new ones, or batteries of different types.
- Clean the battery contacts and also those of the device prior to the battery installation.
- Ensure the batteries are installed correctly with regard to polarity(+ and -).
- Remove batteries from equipment that are not to be used for an extended period of time.
- Remove any defective or ‘dead’ batteries immediately and replace.
- When any battery is removed, you must protect all terminals against short circuits that can result in fires. Protect terminals by completely covering them with an insulating, non-conductive material. Never transport or store a battery where it can come into contact with other batteries or metallic objects. Never store or transport a battery in any location that can become excessively hot. Batteries can become volatile and dangerous if misused, stored or transported incorrectly.
For recycling and disposal of batteries to protect the environment, please check the internet or your local phone directory for local recycling centers and/or follow local government regulations.
For more information on battery housing and location, refer to Step 5 .
PRODUCT FEATURES
- Vintage looking Edison LED light bulbs (E26 base)
- Integrated mounting loops
- Solar battery charging
- Dusk to dawn activation
- 11 m / 36 ft total cable length
- 3V, 0.3W LED replaceable bulbs
PRE-INSTALLATION TEST
- a) Connect the solar panel to the connector on the string lights.
- b) Select ON on the back of the solar panel.
- c) Cover both the panel and the sensor.
- d) The bulbs should now illuminate.
- e) If a bulb does not illuminate, remove and re-screw until the bulb illuminates.
Once the bulbs are all illuminated, turn the switch to OFF and continue with
the installation.
Ensure your solar panel is placed so that its exposure to sunlight is
optimized. Be aware of objects such as trees or property overhangs that may
impede the panel’s ability to generate a charge.
Once the bulbs are all illuminated, turn the switch to OFF and continue with
the installation.
Ensure your solar panel is placed so that its exposure to sunlight is
optimized. Be aware of objects such as trees or property overhangs that may
impede the panel’s ability to generate a charge.
Note: The solar panel should be mounted in a place where the ON/OFF switch is easily accessible.
MOUNTING THE SOLAR PANEL: THE SOLAR PANEL HAS TWO MOUNTING OPTIONS
MOUNTING BRACKET
- If required use the two wall plugs (HI along with the two large screws (G). Install the screws utilizing the two outer holes of the mounting bracket to secure the bracket to the chosen surface.
- Insert the mounting base (D) onto the back of the solar panel (B) aligning the indentations. Use the included small screw (F) to tighten the connection.
- Slide the solar panel down onto the mounting bracket (E) until you feel and hear the connection click into place.
- Adjust the solar panel to the desired angle to optimize sun exposure.
- The angle of the solar panel can be adjusted to maximize sun exposure by loosening, adjusting and then re-tightening the side screw located on the solar panel’s protruding arm.
Note: To disconnect the solar panel from the mounting bracket, press down on the release tab on the bottom of the mounting bracket. With the tab firmly pressed, slide the solar panel upwards and free of the bracket. Some force may be required to remove the panel from the bracket.
GROUND STAKE
To utilize the ground stake (C), connect the two parts of the stake together. The grooved section then fits into the protruding arm of the solar panel. The stake can then be used to mount the panel into the ground.
INSTALLATION OF THE SOLAR STRING LIGHTS
Note: Every fourth bulb should be attached to reduce overall weight or stress on cable.
The solar string lights have a variety of possible ways to be mounted. The following are examples of the most common ways:
- Temporary mounting: Using standard S hooks (not included) or screw hooks (not included) the solar string lights can be mounted utilizing the integrated mounting loops.
- Permanent mounting: Using cable tie wraps or ‘zip lies’ (not included) or using nails or screws into a surface, the solar string lights can be mounted more permanently.
- Guidewire installation: Using S hooks (not included) attach the string lights to a pre-installed guide wire (not included).
- Structural installation: To create a draping effect for the solar string lights attach the first bulb to a structure, then only mount every 3-4th bulb to create the desired effect. Complete the effect by mounting the last bulb to a structure.
- The final step of installation is to connect the solar panel to the string lights. Simply insert the plug located after the final bulb into the wire coming from the solar panel. Tighten the plug by screwing the seal over the connection point. 4
Note: The solar string lights will illuminate for 4-5 hours depending on the charge level of the batteries.
BATTERY REPLACEMENT
The solar string light’s battery (I) is installed on the rear of the solar
panel. Always open the battery compartment with the ON/OFF switch in the OFF
position. Unscrew the back of the battery compartment and remove the backing
piece. Inside you will see the battery.
When replacing the battery, observe the correct polarity and match the battery
specifications with the battery you have removed. Use rechargeable batteries
only.
For this product use one rechargeable 18650 3. ?V lithium-ion battery.
Replace the back of the battery compartment and continue to use the solar
string lights as required.
TROUBLESHOOTING STEPS
- Turn the solar panel to the ON position.
- Turn the solar panel over so no light shines on the glass (you can also cover the panel with a towel or delicate fabric).
- With the panel covered, completely cover the sensor. Once the panel and sensor are totally covered, the lights should now illuminate.
- Should a bulb not illuminate, unscrew and remove that bulb completely. Rescrew as tight as possible untill the bulb illuminates.
HOW TO REPLACE THE BULB?
Step 1
- Input : 3V, 0.3W
- Edison LED Bulb with E26 bas
Carefully unscrew the light bulb.
Step 2
Completely remove the light bulb.
Step 3
Carefully screw in the replacement bulb.
Step 4
Once the bulb is securely screwed into place you are ready to use as required
Only use 3V, 0.3W LED bulbs.
For more information on replacement bulbs, contact Sunforce Products Inc. at info@sunforceproducts.com or call 1-888-478-6435.
SCAN FOR VIDEO
For Further Assistance
- 1-888-478-6435
- info@sunforceproducts.com
- English/French/Spanish language services. 8:30 am – 5 pm Monday -Friday, Eastern Standard Time.
CARE & MAINTENANCE
- Ensure the solar panel remains in a position that optimizes exposure to the sun, especially during the winter months.
- The solar panel should be cleaned with a damp cotton cloth on a regular basis. This will ensure optimal performance and battery charging.
- Utilize the same technique to clean the light bulbs of the solar string lights.
- Never let any abrasive material come into contact with the solar panel or bulbs.
Questions, problems, missing parts?
For assistance with assembly or instruction, parts and customer service, call:
U.S.A & Canada only: 1-888-478-6435
(English/French/Spanish language services).
8:30 am – 5 pm Monday-Friday,
Eastern Standard Time
or email: info@sunforceproducts.com
Distributed by:
- Costco Wholesale Corporation
- P.O. Box 34535 Seattle, WA 98124-1535USA
- 1-800-774-2678
- www.costco.com
Costco France
1 avenue de Bréhat 91140 Villebon-sur-Yvette France
01 80 45 01 10
www.costco.fr
Costco Wholesale Australia Pty Ltd
17-21 Parramatta Road Lidcombe NSW 2141 Australia
www.costco.com.au
Costco Wholesale UK Ltd
- Costco Online UK Ltd Hartspring Lane Watford, Herts WD25 8JS
- United Kingdom
- 01923 213113
- www.costco.co.uk
Costco Wholesale Sweden AB
- Box 614 11411 Stockholm Sweden
- www.costco.se
Cosico Wholesale New Zealand Limited
- 2 Gunton Drive Westgate Auckland 0814New Zealand
- www.costco.co.nz
MADE IN CHINA
FAQS
- Q:I have followed the troubleshooting steps and my light will not illuminate.
- A: Please reach out to our customer care team at info@sunforceproducts.com or call 1-888-478-6435.
Can the wire be extended
No, the solar string light's wiring cannot be extended.
Do the solar string lights require the direct sun to operate
The solar string lights will charge in direct and indirect sunlight. For optimal performance try to ensure the solar panel is orientated to maximize sun exposure.
Are the bulbs replaceable
Yes, the 0.3W LED bulbs are replaceable. Please contact our customer service team and refer to page 15 for additional bull replacement information.
Why do the solar string lights appear to strobe or flash
An undercharged battery generally causes a flashing light. Turn the solar string lights to the OFF position and charge for two full days in strong sun. After these two days of charging, switch to the ON position and use as normal.
Why does my light not illuminate
Refer to the Pre-installation test section of this manual. Make sure that no light is picked up on the solar panel or on the sensor located at the bottom of the solar panel.
What time of battery do my solar string lights require to operate
Each set of solar string lights requires the use of one rechargeable 18650 3-7V Li-lon batteries.
How long do the lights illuminate for
Dependent on the charge and health of the installed batteries the lights should illuminate for between 4-5 hours.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>