SIGOR Nivo Surface Mounted Lights Connection 300mm User Guide

: May 15, 2024
: SIGOR

Table of Contents

SIGOR Nivo Surface Mounted Lights Connection 300mm
Product Information
Product Usage Instructions
Models
Before Starting Work
Included in Delivery
Disclaimer
Assembly
Disposal Instructions according to ElektroG
Contact Information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SIGOR Nivo Surface Mounted Lights Connection 300mm

SIGOR-Nivo-Surface-Mounted-Lights-Connection-300mm-
product

Product Information

Specifications:

Rail length: 30/60/90 cm
Box spacing: 40/70/100 cm

Product Usage Instructions

Safety Instructions:
Before starting any work, ensure to follow all safety precautions mentioned in the manual.

Assembly:

Prepare the bases of the surface-mounted luminaires to be connected.
Thread the wires through the designated opening and connect the connector rail and base with the countersunk head sheet metal screws.
Switch off the circuit and follow safety precautions when preparing and connecting the wires to the terminals.
Install the luminaire bases as an assembly on the ceiling. If connecting more than two luminaires, repeat the steps provided.
Note: The connector rails must not be shortened.

Disposal Instructions:
Sigor luminaires should be returned to their dealer or an electronic waste collection point at the end of their life. Do not dispose of them in household waste.

FAQ:

Q: What should I do if I want to connect more than two luminaires?
A: If you want to connect more than two luminaires, repeat the steps described in the assembly section for each additional luminaire. Ensure not to shorten the connector rails.

Models

4815401 Nivo® Connector 30 cm black
4815501 Nivo® Connector 60 cm black
4815601 Nivo® Connector 90 cm black
4815701 Nivo® Connector 30 cm white
4815801 Nivo® Connector 60 cm white
4815901 Nivo® Connector 90 cm white

Before Starting Work

Please read this installation and operating manual carefully and follow all instructions diligently. The installation of this luminaire must be carried out by a qualified electrician for your safety. Adhere to safety regulations and health protection measures, especially the appropriate selection of VDE 0100. Before starting the installation, isolate the relevant part of the system while observing the five safety rules. Check the luminaire for integrity before commissioning; only operate undamaged products!

Intended Use
The Nivo® Connectors ensure protection class IP30 and are intended for installation on solid and load-bearing surfaces indoors at ambient temperatures of -20 to +40°C with 220-230 V 50Hz AC. The proper use also includes compliance with all information in this manual, especially the safety instructions.

Caution:
Use only connection wires with protective coating installed in the connectors. Any other use is considered improper and may result in damage to property or personal injury.

Disposal
Sigor luminaires comply with RoHS and should be returned to their dealer or an electronic waste collection point at the end of their life. Please do not dispose of them in household waste.

Included in Delivery

Nivo® Connector with connecting wires
4x ST2,2×5 countersunk head sheet metal screws
This installation and operating manual

Disclaimer

Note:
In case of non-compliance with this manual and improper use, there is no warranty claim, and Sigor Licht GmbH assumes no liability in such cases.

Assembly

Caution:
Use only connection wires with a protective coating.

Prepare the bases of the surface-mounted luminaires to be connected.
Take the following materials out of the packaging:
- 4x ST2.2×5 countersunk head sheet metal screws
- 1x Connector rail
Thread the wires through the designated opening and connect the connector rail and base with the countersunk head sheet metal screws.
Switch off the circuit, and observe safety precautions! Prepare the wires and connect them to the terminals. Please follow the instructions of the respective luminaire for the main connection.
Install the luminaire bases as an assembly on the ceiling. $SIGOR-Nivo-Surface-Mounted-Lights-Connection-300mm-fig- $5$$
If you want to connect more than two luminaires, repeat the described steps.
Note: The connector rails must not be shortened! $SIGOR-Nivo-Surface-Mounted-Lights-Connection-300mm-fig- $6$$

Disposal Instructions according to ElektroG

„Owners of old appliances must dispose of them separately from unsorted municipal waste. Old appliances must not be disposed of in household waste but through special collection and return systems.

Owners of old appliances must separate batteries and accumulators not enclosed by the old appliance, as well as lamps that can be removed undamaged from the old appliance, before handing them over to a collection point. This does not apply if old appliances are handed over to public waste disposal authorities and are separated there for preparation for reuse. Owners of old appliances from private households can dispose of them free of charge at collection points of public waste disposal authorities or return points set up by manufacturers and distributors by ElektroG.

You can find an online directory of collection and return points here: https://www.e-schrott-entsorgen.org/.

Some old appliances contain sensitive personal data, especially devices in the information and telecommunications technology sector such as computers and smartphones. It is in your interest to note that you are responsible for deleting the data on the old appliances to be disposed of. The symbol of a crossed-out waste bin on electrical and electronic devices means that the device must be disposed of separately from unsorted municipal waste at the end of its service life.“