sentiotec S-WIFI01 MySentio WiFi Instruction Manual
- June 9, 2024
- sentiotec
Table of Contents
sentiotec S-WIFI01 MySentio WiFi
Installation
About this instruction manual
THIS IS A QUICK START GUIDE. The installation and operating instructions can also be found in the downloads section of our website: www.sentiotec.com/downloads
Symbols used for warning notices
In these instructions for installation and use, a warning notice located next
to an activity indicates that this activity poses a risk. Always observe the
warning notices. This prevents damage to property and injuries.
Intended use
Sentiotec WiFi is used to control the sauna remotely. A sauna heater controlled by the remote start function of the sauna control unit must pass the combustion test as specified in EN 60335-2-53 paragraph 19.101. If the heater does not meet this requirement, an appropriate safety precaution must be used (for example: safety switch-off or door monitoring) Any use exceeding this scope is considered improper use. Improper use can result in damage to the product, severe injuries or death..
Safety information for the installer
- Installation and connection work on the devices may only be carried out with the power supply disconnected.
- Observe the installation instructions for the sauna control unit used.
- Also comply with the regulations applicable at the installation location.
- For your own safety, consult your supplier in the event of prob-lems that are not explained in sufficient detail in the installation instructions.
Safety information for the user
- The WiFi must not be used by children under 8 years of age.
- The WiFi may only be used by children over 8 years of age, by persons with limited psychological, sensory or mental capabilities or by persons with a lack of experience/knowledge under the following conditions:
- They are supervised.
- They have been shown how to use the device safely and are aware of the hazards that could occur.
- Observe the operating instructions for the sauna control unit used.
- For your own safety, consult your supplier in the event of prob-lems that are not described in sufficient detail in the operating instructions.
Product Description
Scope of delivery
- WiFi adapter
- 1 pc. 1 m Ethernet cable, 8-pin RJ45
- Installation material
- Assembly instructions
Optional accessories
- Door sensor system (1-052-722 / SAB00102)
- Door sensor set (1-052-723 / SAB00103)
- Safety shutdown (SFE-xxxxx)
Product features
Sentiotec WiFi enables the functions of all existing sauna control units to be operated using devices such as smartphones and tablets. This is done using the MySentio app in a local network (WiFi), which is available free of charge for Android (Google Play Store) and for iOS (App Store). Compatible sauna control units:
- home.com4 RS485 (1-052-984 HC4-B-RS485 / 1-052-985 HC4-W-RS485)
- Pro B2 (1-015-455 / PRO-B2)
- Pro B3 (1-015-457 / PRO-B3)
- Pro C2 (1-015-448 / PRO-C2)
- Pro C3 (1-015-451 / PRO-C3)
- Pro D (only in combination with BUS-CON-D / 1-053-348)
Standard-compliant operation
To ensure standard-compliant operation, safety devices must be installed in
accordance with the operating instructions for your sauna control unit.
Installation and connection
Work may only be carried out when the power has been disconnected. During installation, observe the technical data on Page 8.
Interference can impair signal transmission
-
Route all data cables separately from other mains cables and control cables.
Protect cables with only one layer of insulation by using a conduit (double insulation). -
Secure the WiFi module somewhere near the sauna control unit and within the range of its network (WiFi) using the screws provided.
-
Sentiotec WiFi is connected to the sauna control unit using the 8-pin Ethernet cable in accordance with the following diagrams:
-
Make a note of the serial numbers (10 digits) of your devices to ensure you can enter them in the app later on.
Mounting and connecting MySentio WiFi
Connection to home.com4
Connection to PRO B (B2, B3) and PRO
Connection to PRO D (D2, D2I, D3, D3I)
Commissioning
- To activate remote start, refer to the operating instructions for the respective control unit.
- Download the “MySentio” app onto your smartphone or tablet
- Open the app and sign up.
- Following the instructions provided in the app.
Follow the instructions in the user manual available at the following link: www.sentiotec.com/de/downloads/bedienungsanleitungen
Maintenance
The device is maintenance-free. Updates take place automatically.
Disposal
- Dispose of packaging materials in accordance with the applicable waste disposal regulations.
- Used devices contain reusable materials as well as hazardous substances. Therefore, do not dispose of your used device with household waste, but do so in accordance with the locally appli-cable regulations.
Technical data
Ambient conditions
- Ambient temperature: -20 °C to +40 °C
- Protection class (protected against splashing water): IP 20
- Minimum requirement WiFi 2.4 GHz: 1 Mbit
Control unit
- Dimensions: 83 x 56 x 24.5 mm
- Operating voltage: 24 V DC max. 1W
Connection cables
- Power supplied by Ethernet cable: 8-pin RJ45 max. 30m
GLOBAL
- HARVIA
- P.O. Box 12, Teollisuustie 1-7, 40951 Muurame,
- FINLAND T +358 207 464 000
- harvia@harvia.fi
- www.harvia.fi
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>