SIGOR Nivo  Pendant Recessed Installation Guide

SIGOR Nivo  Pendant Recessed

Specifications

• Brand: Sigor Licht GmbH
• Model: Not specified
• Dimensions: Not specified
• Power Source : Electric
• Light Source : LED
• Compliance: RoHS
• Warranty: Contact Sigor Licht GmbH for details

Product Usage Instructions

Safety Instructions:
Before starting any work, make sure to read and follow the installation and operating manual carefully. The installation of this luminaire must be carried out by an electrician for safety reasons. Always follow safety and health regulations, especially VDE 0100 guidelines. Be sure to isolate the relevant part of the system following the safety rules before starting the installation.

Assembly:

1. Switch off the corresponding circuit and disconnect the power supply indoors.
2. Create a ceiling cutout with a diameter of 102 mm.
3. Connect the LED driver’s terminal block to the disconnected power supply.
4. Loosen the strain relief screws and adjust the cable to the desired pendant length.
5. Push both spring clips upwards and insert the pendant light into the ceiling.
6. Observe the recommended minimum distances in the ceiling, ensuring not to cover the luminaire and driver with insulating material.
7. After successful initial operation, the installation is complete.
8. For plasterboard installation, follow step 1 according to separate instructions.

Lens Change:
The light source of this luminaire is not user-replaceable and should only be changed by Sigor Licht GmbH or an authorized service technician. Follow proper safety precautions to avoid any risk of electric shock.

FAQ

• What should I do if I need to replace the light source?
  The light source of this luminaire should only be replaced by Sigor Licht GmbH or an authorized service technician to ensure safety and proper functionality.

• How should I dispose of the luminaire at the end of its life?
  Sigor luminaires are RoHS compliant and should be returned to their dealer or an electronic waste collection point for proper disposal. Do not dispose of them in household waste.

Before starting work

Please read and follow this installation and operating manual carefully. The installation of this luminaire must be carried out by an electrician for your safety. Follow safety and health regulations for all activities, especially the relevant selection of VDE 0100. Before starting the installation, isolate the relevant part of the system following the five safety rules. Check the luminaire for integrity before commissioning, only operate undamaged products!

Intended Use

The Nivo® pendant lights ensure IP30 protection and are intended for installation on solid and load-bearing surfaces indoors at ambient temperatures of -20 to +40°C, with 220-230 V 50Hz AC voltage. Proper use also includes observing all information in this manual, especially the safety instructions. Note: The luminai- res are not intended to be covered with insulating material such as mineral wool. Any other use is conside- red improper and may result in property or personal damage.

Non-user-replaceable light source

The light source of this luminaire may only be replaced by Sigor Licht GmbH or an authorized service tech- nician or a similarly qualified person. (EN 60598-1 3.3.21) Caution! Risk of electric shock.

Disposal

Sigor luminaires are RoHS compliant and should be returned to their dealer or an electronic waste collection point at the end of their life. Do not dispose of them in household waste.

Scope of delivery

• Nivo® Pendant Light Recessed with 5 years Sigor functional guarantee
• This installation and operating manual
• Cotton gloves

Disclaimer

Note: In case of non-compliance with this manual and improper use, there is no warranty claim; Sigor Licht GmbH assumes no liability in such cases.

Installation

1. Switch off the corresponding circuit, disconnect the power supply indoors
   Create a ceiling cutout with a diameter of 102 mm

2. Connect the LED driver‘s terminal block to the disconnected power supply

3. Loosen the strain relief screws and adjust the cable to the desired pendant length.

4. Push both spring clips upwards and insert the pendant light into the ceiling.

5. Observe the recommended minimum distances in the ceiling, do not cover the luminaire and driver with insulating material.
6. After successful initial operation, the installation is complete.

7. For plasterboard installation, please follow step 1 according to the separate instructions.

Lens Replacement

The lens insert (a) is held in the luminaire by three magnets; with a slight rotation of the lens insert in the luminaire (b), the magnets separate, and the lens insert (b) falls out.

Warning

• The luminaire head can become hot up to 60°C during operation.
• Please wait a moment after switching off or use the included gloves to work on the luminaire immediately.

Disposal Instructions according to ElektroG

• Owners of old devices must dispose of them separately from unsorted municipal waste. Old devices must not be disposed of with household waste but through special collection and return systems.

• Owners of old devices must separate batteries and accumulators not enclosed by the old device, as well as lamps that
  can be removed from the old device without destruction, from the old device before handing it over to a collection point. This does not apply if old devices are handed over to public-law waste disposal authorities and are separated there for the purpose of preparing them for reuse. Owners of old devices from private households can hand them in free of charge at the collection points of public-law waste disposal authorities or at the collection points set up by manufacturers and distributors in accordance with the ElektroG.

• An online directory of collection and return points can be found here: https://www.e-schrott-entsorgen.org/

• Some old devices contain sensitive personal data, especially devices in information and communication technology such as computers and smartphones. It is in your own interest to ensure that you are responsible for deleting the data on the old de- vices to be disposed of. The symbol of a crossed-out dustbin on electrical and electronic equipment means that the device must be disposed of separately from unsorted municipal waste at the end of its service life.“

Warranty Conditions

• The warranty is exclusively for consumers. Warranty protection applies only to products purchased within the Federal Republic of Germany. The warranty period begins on the invoice date.

• If material or manufacturing defects in the goods you purchased arise during this period and affect the function of the product, we will provide you with a new, defect-free product as part of this warranty. This does not apply in the case of a battery performance fault.

• In the event of a warranty claim, please contact us as the warranty provider:
  Sigor Licht GmbH Phone: +49 2339 1261 0 Eichenhofer Weg 81 Email: reklamation@sigor.de 42279 Wuppertal

• Warranty claims are excluded for damage to the goods due to normal wear and tear and improper or non-intended use or treat- ment. A prerequisite for claiming warranty service is that you enable us to examine the warranty case (e.g., by sending the goods). If you send the goods for this purpose, please ensure that damage to the goods during transport is avoided through appropriate packaging. A copy of the invoice must be included with the goods shipment for the warranty claim to be reviewed, so we can ver- ify whether the warranty period has been adhered to. Alternatively, you can send the copy of the invoice to us by email. We reserve the right to reject the warranty service if it cannot be determined whether the warranty period has expired.

• There are no shipping costs for justified warranty claims. In this case, we will refund any shipping costs for the return of the defec- tive goods and bear the costs of shipping a new, defect-free product to you.
  Important Note: This warranty does not limit your statutory rights. Instead, the warranty promise is separate from the statutory warranty rights to which you are entitled free of charge.

ABOUT COMPANY

• Sigor Licht GmbH
• Eichenhofer Weg 81 42279 Wuppertal Germany
• Tel. +49 2339 1261-0
• Fax +49 2339 1261-61
• www.sigor.de
• info@sigor.de

References

• Sigor – Sigor
• E-Schrott Entsorgung in Deiner Nähe – Kostenlos, Sicher und Einfach – Plan-E

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>