renkforce 2923234 LED Desk Clamp Lamp Instruction Manual
- May 15, 2024
- renkforce
Table of Contents
Operating Instructions
LED Desk Clamp Lamp
Item no: 2923234
http://www.conrad.com/downloads
Intended use
The product is an LED desk lamp.
The product is intended for indoor use only. Do not use it outdoors.
Contact with moisture must be avoided under all circumstances.
If you use the product for purposes other than those described, the product
may be damaged.
Improper use can result in short circuits, fires, electric shocks or other
hazards.
The product complies with the statutory national and European requirements.
For safety and approval purposes, you must not rebuild and/or modify the
product.
Read the operating instructions carefully and store them in a safe place. Make
this product available to third parties only together with the operating
instructions.
All company names and product names are trademarks of their respective owners.
All rights reserved.
Delivery contents
- Product
- Clamp
- Operating instructions
Operating instructions
Download the latest operating instructions from www.conrad.com/downloads or scan the QR code shown. Follow the instructions on the website.
Description of symbols
The following symbols are on the product/appliance or are used in the text:
| Protection class 2 (double or reinforced insulation, protective insulation).
---|---
| This product must only be used in dry, enclosed indoor areas. It must not
become damp or wet.
| The symbol warns of dangerous voltage that can lead to personal injury by
electric shock.
| The symbol warns of hazards that can lead to personal injury.
|
Read the operating instructions carefully.
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling, we assume no liability for any resulting personal injury or
damage to property. Such cases will invalidate the warranty/guarantee.
5.1 General
- The product is not a toy. Keep it out of the reach of children and pets.
- Do not leave packaging material lying around carelessly. This may become dangerous playing material for children.
- If you have questions which remain unanswered by this information product, contact our technical support service or other technical personnel.
- Maintenance, modifications and repairs must only be completed by a technician or an authorised repair centre.
5.2 Handling
- Handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.
5.3 Operating environment
- Do not place the product under any mechanical stress.
- Protect the appliance from extreme temperatures, strong jolts, flammable gases, steam and solvents.
- Protect the product from high humidity and moisture.
- Protect the product from direct sunlight.
5.4 Operation
- Consult an expert when in doubt about the operation, safety or connection of the product.
- If it is no longer possible to operate the product safely, take it out of operation and protect it from any accidental use. DO NOT attempt to repair the product yourself. Safe operation can no longer be guaranteed if the product:
– is visibly damaged,
– is no longer working properly,
– has been stored for extended periods in poor ambient conditions or
– has been subjected to any serious transport-related stresses.
5.5 Mains cable
Do not modify or repair mains supply components including mains plugs,
mains cables, and power supplies. Do not use damaged components. Risk of death
by electric shock!
-
The mains outlet must be located near to the device and be easily accessible.
-
Never plug in or unplug the mains plug when your hands are wet.
-
Never pull the mains plug from the socket by pulling at the cable. Always pull it from the mains socket using the intended grips.
-
Unplug the mains plug from the mains socket if you do not use the device for an extended period of time.
-
Disconnect the mains plug from the mains socket in thunderstorms for reasons of safety.
-
Make sure that the mains cable is not squeezed, bent, damaged by sharp edges or put under mechanical stress.
-
Avoid excessive thermal stress on the mains cable from extreme heat or cold.
-
Do not modify the mains cable. Otherwise the mains cable may be damaged. A damaged mains cable can cause a deadly electric shock.
-
Do not touch the mains cable if it is damaged.
– First, power down the respective mains socket (e.g. via the respective circuit breaker) and then carefully pull the mains plug from the mains socket.
– Never use the product if the mains cable is damaged. -
A damaged mains cable may only be replaced by the manufacturer, a workshop commissioned by the manufacturer or a similarly qualified person, so as to prevent any danger.
-
Ensure that cables are not pinched, kinked or damaged by sharp edges.
-
Always lay cables so that nobody can trip over or become entangled in them. This poses a risk of injury.
5.6 LED light
- Do not look directly into the LED light!
- Do not look into the beam directly or with optical instruments!
Setup
- Insert the lamp into the desk clamp.
- Tighten the clamp fixing screw to secure the lamp.
- Loosen the desk clamp and attach the lamp to a desk.
- Tighten the desk clamp to secure the lamp to the desk.
Operation
- Connect the mains plug to the mains supply.
- Rotate the dial at the top of the lamp shade to switch the light on and off and control the dimming.
Cleaning
Important:
-
Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions.
They damage the housing and can cause the product to malfunction. -
Do not immerse the product in water.
- Remove all accessories and disconnect the product from the power supply.
- Clean the product with a dry, fibre-free cloth.
Disposal
**** This symbol must appear on any electrical and electronic equipment
placed on the EU market. This symbol indicates that this device should not be
disposed of as unsorted municipal waste at the end of its service life.
Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose
of it separately from unsorted municipal waste. Spent batteries and
accumulators, which are not enclosed by the WEEE, as well as lamps that can be
removed from the WEEE in a non-destructive manner, must be removed by end
users from the WEEE in a non-destructive manner before it is handed over to a
collection point.
Distributors of electrical and electronic equipment are legally obliged to
provide free takeback of waste. Conrad provides the following return options
free of charge (more details on our website):
- in our Conrad offices
- at the Conrad collection points
- at the collection points of public waste management authorities or the collection points set up by manufacturers or distributors within the meaning of the ElektroG
End users are responsible for deleting personal data from the WEEE to be
disposed of.
It should be noted that different obligations about the return or recycling of
WEEE may apply in countries outside of Germany.
Technical data
10.1 General
This product contains a light source of energy efficiency class F.
Input voltage …………………………….. 200 – 240 V/AC, 50/60 Hz
Power consumption …………………… max. 9 W
Protection class ………………………… II
Dimmable ………………………………… yes
Brightness………………………………… max. 900 lm (of LED module)
Table clamp width……………………… max. 45 mm (adjustable)
Operating conditions………………….. -20 to +40 °C, 20 – 80 % RH (non-condensing)
Storage conditions…………………….. -20 to +50 °C, 20 – 80 % RH (non-condensing)
Dimensions (W x H x D) …………….. approx. 176 x 700 x 400 mm
Weight (approx.) ……………………….. 950 g
10.2 LED
Efficiency …………………………………. 100 lm/W
Colour rendering index (CRI)………. 80
Colour temperature……………………. 3000 K
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240
Hirschau ( www.conrad.com ).
All rights including translation reserved. Reproduction by any method (e.g.
photocopying, microfilming or the capture in electronic data processing
systems) requires prior written approval from the editor. Reprinting, also in
part, is prohibited.
This publication reflects the technical status at the time of printing.
Copyright by Conrad Electronic SE.
*2923234_V2_1223_jh_mh_en 27021598903196427-2 I4/O2 en
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>