Troy F1724 Lonnie 4 Light 20 Wide Pendant User Manual
- May 15, 2024
- Troy
Table of Contents
Troy F1724 Lonnie 4 Light 20 Wide Pendant
Product Specifications:
- Brand: Hudson Valley Lighting
- Model: Levant F1724
- Compatible Bulb Type: 15 Watt Type G25 Lamp
- Website: www.hvlgroup.com
Product Usage Instructions
Fixture Installation Steps:
- Attach the MOUNTING PLATE (A) onto the junction box using the MOUNTING SCREWS (B).
- Thread the NIPPLE (C) onto the COLLAR LOOP (H) and secure it onto the MOUNTING PLATE (A).
- Attach the CHAIN (K) to the FIXTURE ASSEMBLY (L) at the desired height.
- Feed the wires through the CHAIN (K), CANOPY (J), COLLAR LOOP (H), NIPPLE (C), and MOUNTING PLATE (A).
- Connect the Ground wire and Neutral wire following safety precautions.
- Connect the fixture’s SPT hot wire to the hot wire in the junction box.
- Secure all connections and push wires back into the junction box.
- Attach the SHADES onto the FIXTURE ASSEMBLY (L) and secure using THREADED SOCKET RING (P).
- Screw the recommended BULB (Q) into the SOCKET of the FIXTURE ASSEMBLY (L).
- Restore power to the outlet at the breaker or fuse box.
Frequently Asked Questions (FAQ):
-
Q: What type of bulb should I use with this fixture?
A: This fixture is rated for use with a 15 Watt Type G25 Lamp. Do not exceed the recommended wattage to avoid damage. -
Q: How do I ensure proper wiring connections during installation?
A: Follow the provided instructions carefully, making sure to connect the Ground, Neutral, and Hot wires correctly. Use approved fasteners and secure all connections properly to prevent any electrical hazards. -
Q: Can I install this fixture on any type of junction box?
A: This fixture is designed to be mounted on standard round or octagon junction boxes. Ensure that the junction box is securely attached to the building structure before installation.
WARNING/CAUTION
- DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.
- TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED FACTORY TRAINED TECHNICIAN.
- CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER USE.
- UNPACK FIXTURE, PARTS AND PARTS BAG(S) BEFORE DISCARDING THE CARTON. MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR TO INSTALLATION FOR ANY DAMAGE. HVLG DOES NOT PAY OR REIMBURSE ELECTRICIAN FEES. FIXTURE MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. SEE WARRANTY FOR EXCEPTIONS.
- PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS.
FIXTURE INSTALLATION
- Attach the MOUNTING PLATE (A) onto the junction box using the MOUNTING SCREWS (B). This fixture is designed to be mounted on standard round or octagon junction box. The junction box must be securely mounted to the structure of the building.
- Remove the SCREW COLLAR (I) from the COLLAR LOOP (H). Fully thread the NIPPLE (C) onto the COLLAR LOOP (H). Thread the HEX NUT (E) onto the NIPPLE (C) along with TOOTH WASHER (D). Then thread the NIPPLE (C) onto the MOUNTING PLATE (A). Adjust the NIPPLE (C) so that the threads of the COLLAR LOOP (H) extends 1″ beyond the CANOPY (J). Secure using HEX NUT (E).
- Open the end link the of the CHAIN (K) and attach to the FIXTURE ASSEMBLY (L) at the desired height. Slide the SCREW COLLAR (I) and the CANOPY (J) onto the CHAIN (K). Open the link on other end of the CHAIN (K) then attach unto the COLLAR LOOP (H). Feed the wires through the CHAIN (K) , SCREW COLLAR (I), CANOPY (J), COLLAR LOOP (H), NIPPLE (C), and MOUNTING PLATE (A).
- Cut off excess wires, and strip the insulation off the end of the leads.
- Attach the Ground wire to the ground inside the junction box (Generally green or bare copper wire) or the GROUND SCREW (F) on the MOUNTING PLATE (A). NEVER CONNECT GROUND WIRE TO “HOT” WIRE! FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
- Connect the fixture’s SPT Neutral (SPT WIRE WITH NO WRITINGS) wire lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (G). Starting 1″ below the fastener, tightly wrap the connection with electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!
- Connect the fixture’s SPT hot (SPT WITH WRITINGS) wire lead to the hot (Generally black) wire in the junction box. Fasten the joined wires same as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
- Push the wires back into the junction box. Lift up the CANOPY (J) up to the ceiling, and screw the SCREW COLLAR (I) onto the COLLAR LOOP (H).
- Attach the LARGE SHADE (M), MEDIUM SHADE (N), and SMALL SHADE (O) onto the FIXTURE ASSEMBLY (L) and secure using THREADED SOCKET RING (P).
- Screw the BULB (Q) up into the SOCKET of the FIXTURE ASSEMBLY (L). THIS FIXTURE IS RATED FOR 15 WATT TYPE G25 LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE!
- Restore power to the OUTLET at the breaker or fuse box.
Website: www.hvlgroup.com
References
Read User Manual Online (PDF format)
Loading......