ADLER MS 4060 MESKO Blender User Manual
- June 6, 2024
- ADLER
Table of Contents
MS 4060
user manual
SAFETY CONDITIONS IMPORTANT INSTRUCTIONS ON SAFETY OF USE PLEASE
READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
The warranty conditions are different if the device is used for commercial
purposes.
-
Before using the product please read carefully and always comply with the following instructions. The manufacturer is not responsible for any damages due to any misuse.
-
The product is only to be used indoors. Do not use the product for any purpose that is not compatible with its application.
-
The applicable voltage is 220-240V~, 50/60Hz. For safety reasons, it is not appropriate to connect multiple devices to one power outlet.
-
Please be cautious when using around children. Do not let the children play with the product. Do not let children or people who do not know the device use it without
supervision. -
WARNING: This device may be used by children over 8 years of age and persons with reduced physical, sensory or mental capabilities, or persons without experience or
knowledge of the device, only under the supervision of a person responsible for their safety, or if they were instructed on the safe use of the device and are aware of the
dangers associated with its operation. Children should not play with the device. Cleaning and maintenance of the device should not be carried out by children unless they are over 8 years of age and these activities are carried out under supervision. -
After you are finished using the product always remember to gently remove the plug from the power outlet holding the outlet with your hand. Never pull the power cable!!!
-
Never put the power cable, the plug, or the whole device into the water. Never expose the product to atmospheric conditions such as direct sunlight or rain, etc. Never use the product in humid conditions.
-
Periodically check the power cable condition. If the power cable is damaged the product should be turned to a professional service location to be replaced in order to avoid
hazardous situations. -
Never use the product with a damaged power cable or if it was dropped or damaged in any other way or if it does not work properly. Do not try to repair the defective product yourself because it can lead to electric shock. Always turn the damaged device to a professional service location in order to repair it. All the repairs can be done only by authorized service professionals. The repair that was done incorrectly can cause hazardous situations for the user.
-
Never put the product on or close to the hot or warm surfaces or the kitchen appliances like the electric oven or gas burner.
-
Never use the product close to combustibles.
-
Do not let the cord hang over the edge of a counter or touch hot surfaces.
-
Never leave the product connected to the power source without supervision. Even when use is interrupted for a short time, turn it off from the network, unplug the power.
-
In order to provide additional protection, it is recommended to install a residue current device (RCD) in the power circuit, with a residual current rating of not more than 30 mA. Contact a professional electrician in this matter.
-
The exchange of accessories may only be carried out with the device switched off.
-
The blades are very sharp. The highest caution is offered. Before replacing the mixers, unplug the power cord from the wall outlet.
-
Only use original accessories that are included in the scope of supply.
-
Do not cover the ventilation openings in the housing during operation.
-
For washing the case, do not use any heavy cleaning agents because they can be used to remove graphical information symbols, e.g. Signs, warning photograms, etc.
-
Never use the appliance for hot oil or grease (hot products).
-
Never touch with wet hands.
-
The appliance is not intended for crushing ice, bone, and other hard products or for grinding nuts and coffee.
-
During the mixing process, never place your hands or cutlery into the container.
-
Observe the maximum uninterrupted operating time of the unit of 50 seconds. After the continuous operating time of 50 seconds, wait 4 minutes before turning the unit back on. Exceeding the operating time of the appliance and the absence of sufficient breaks can lead to irreversible engine damage.
-
When the appliance is aged, unplug it from the mains before cleaning.
-
Before first use, wash thoroughly and dry the appliance (see: Cleaning and maintenance).
DEVICE DESCRIPTION
| 1A – plug | 1B – cover |
|---|
1C – blender cup
1E – speed control button I| 1D – body
1G – base| 1F – speed control button II
DEVICE OPERATION
Before first use:
1. Remove all stickers from the housing, cup and cover of the blender.
2. Wash the blender cup in warm water with washing-up liquid, rinse
thoroughly, dry the inside and outside of the cup.
Blender operation:
- Put the blender main body (1D) on a stable, level surface.
- Place the blender cup (1C) on the body (1D).
- Remove cover (1B) from the blender cup (1C), put in the ingredients to be mixed. In order to avoid overflow, the level of ingredients in the cup should not exceed ¾ of the cup’s height.
- Connect the power plug to the power outlet.
- Turn the blender on by holding an adequate button (1E or 1F) depending on the wanted rotation speed.
- After the mixed products have proper consistency, turn the blender off by releasing the button (1E or 1F). Wait until the blades stop. Remove the power plug from the power outlet. Remove the cup.
NOTICE: During mixing always hold a cup (1C) with your hand.
NOTICE: Do not allow continuous operation of blender for longer than 3 minutes.
CLEANING AND MAINTENANCE
Make are sure that the blender is disconnected from the power.
1. Wash the cup, cover, and blades in water with washing-up liquid. In order
to wash the cup thoroughly put some water with washing-up liquid in the cup,
connect the blender to the power, and operate it for a short period of time.
Then pour out the water, rinse thoroughly, and dry.
2. Clean the stained body (1D) with a moist cloth, and then wipe dry.
NOTICE: Don’t immerse the blender body in water or other liquids.
NOTICE: Do not wash any blender parts in dishwashers.
TECHNICAL DATA
Power: 250W Max.: 500W
Voltage: 220-240V~50/60Hz
To protect your environment: please separate carton boxes and plastic bags and dispose of them in corresponding waste bins. The used appliances should be delivered to the dedicated collecting points due to hazardous components, which may affect the environment. Do not dispose of this appliance in the common waste bin.